12. Problem 6: A hollow cylindrical steel column has an outer diameter of 4 inches and inner diameter of 3.5 inches. The column is separated from the concrete foundation by a square bearing plate. If the working compressive stress is 26000 psi for the column, find the force P (in Ibs) that maybe applied to the column. 4 in. 3.5 in - 7 in Your answer 13. In Problem 6, if the working bearing stress is 1200 psi for concrete, find the value of force P (in Ibs) that maybe applied to the column. Your answer 14. In Problem 6, what is the largest force P (in Ibs) that can be applied to the column.

12. Problem 6: A hollow cylindrical steel column has an outer diameter of 4 inches and inner diameter of 3.5 inches. The column is separated from the concrete foundation by a square bearing plate. If the working compressive stress is 26000 psi for the column, find the force P (in Ibs) that maybe applied to the column. 4 in. 3.5 in - 7 in Your answer 13. In Problem 6, if the working bearing stress is 1200 psi for concrete, find the value of force P (in Ibs) that maybe applied to the column. Your answer 14. In Problem 6, what is the largest force P (in Ibs) that can be applied to the column.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression is 400 MPa. The total load P that may be supported by the pad is 900 kN. Using a factor or safely 3.0 with respect to ultimate strength, determine the outer diameter of the pier if the thickness, is of the cross section is 12 mm.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Ql- Compare the maximum stress induced into a rectangular plate 100mm long into x-axis direction, 50mm width into y-axis direction and 10mm thickness into z-axis direction is subjected to tensile load of 10kN into y-axis direction for bellow cases: 1- As a solid plate. 2- The same plate with a Circle hole 10mm diameter in xy-plane in the center the plate.
PRELIMINARY DISCUSSIONS PME 412 - MACHINE DESIGN 1 PROBLEM: Find the values and plot the distribution of stress over the cross section of the upright of the figure. Locate the point of zero stress. 9,000 N 60 mm thick - 100 mm -50 mm
. A steel boiler 2.5 m in diameter has a wall thickness of 25 mm. The internal pressure is 1.6 MPa. Calculate the factor of safety if the maximum permissible stress for it is 250 MPa?
The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a pin. Find the minimum diameter of pin is used. Take oall = 243 ksi for pin material.
Problem Solving: Show your Solution 1. A sculpture weighing 10,000 N rests on a horizontal surface at the top of a 6.0-m-tall vertical pillar. The pillar’s cross-sectional area is 0.20 m20.20 m2 and it is made of granite with a mass density of 2700kg/m3.2700kg/m3. Find the compressive stress at the cross-section located 3.0 m below the top of the pillar and the value of the compressive strain of the top 3.0-m segment of the pillar. 2. A 2.0-m-long steel rod has a cross-sectional area of 0.30cm2.0.30cm2. The rod is a part of avertical support that holds a heavy 550-kg platform that hangs attached to the rod’s lower end.Ignoring the weight of the rod, what is the tensile stress in the rod and the elongation of the rodunder the stress? 3. In a hydraulic press, a 250-liter volume of oil is subjected to a 2300-psi pressure increase. If the compressibility of oil is 2.0×10−5/atm,2.0×10−5/atm, find the bulk strain and the absolute decrease in the volume of oil when the press is operating.…