A deep braced cut in clay is shown in Figure 2. a) Determine and draw the lateral soil pressure distribution on the system b) Assuming that the design load in each strut shall not exceed 500 kN, determine the maximum horizonal spacing (s) between the struts 5.0 m 1.8 m A 2.8 m B 2.8 m 1.0 m Cu =50 kPa y= 19 kN/m

A deep braced cut in clay is shown in Figure 2. a) Determine and draw the lateral soil pressure distribution on the system b) Assuming that the design load in each strut shall not exceed 500 kN, determine the maximum horizonal spacing (s) between the struts 5.0 m 1.8 m A 2.8 m B 2.8 m 1.0 m Cu =50 kPa y= 19 kN/m

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter19: Braced Cuts

Section: Chapter Questions

Problem 19.3P: A braced cut shown in Figure P19.3 is to be made to a depth of 9.0 m in a saturated clay deposit...

See similar textbooks

Similar questions

Given: 1. Structural Component: Beam 300 mm x 400 mm Column 400 mm x 400 mm Slab thickness 110 mm 2. Dead Load: Super Imposed dead load = 4.5 KPa (including slab weight) CHB = 3.11 KPa 3. Seismic Parameter: Soil Profile - Sb Closest distance to the source - 10 km Ductility Coefficient R = 8.0 Seismic Zone Z=0.40 Ct = 0.0731 A. Compute TOTAL LATERAL FORCES in the 2nd floor? B. Compute LATERAL FORCES in the 3rd floor?
eiches : Two-way slab system (6.1*6.1 m) as shown in Fig. 1, subjected to a live load of 2 kN/m² and superimposed dead load of 3.5 kN/m². Design the panel $2 for max positive and negative moments. The column dimension 300* 300 mm and the supporting beams are 300 mm width. Use fe=21 MPa and fy = 420 MPa arks). Fig.1 S2 6.1m 6.1m
Q4: Use the rectangular loaded area to calculate the increase in vertical stresses at points (A) and (B) due to the loaded area of footing. Choose figure (1) or (2). 121 Top view Top view B J-2m- B CLAY 1 CLAY 1 CLAY 2 A 10 m X 10 m 9-150 kN/m² TTTTTT INCOMPRESSIBLE Figure (1) B G.W.T CLAY 1 CLAY 1 CLAY 2 YA' 10 m X 10 m 9-150 KN² INCOMPRESSIBLE Figure (2) Thm G.W.
Given: 1. Structural Component: Beam 300 mm x 400 mm Column 400 mm x 400 mm Slab thickness 110 mm 2. Dead Load: Super Imposed dead load = 4.5 KPa (including slab weight) CHB = 3.11 KPa 3. Seismic Parameter: Soil Profile - Sb Closest distance to the source - 10 km Ductility Coefficient R = 8.0 Seismic Zone Z=0.40 Ct = 0.0731 A. Compute the DESIGN BASE SHEAR (V = Cv*I*W /R*T). B. Compute the Minimum DESIGN BASE SHEAR (V =0.11Ca*I*W).
Calculate the geostatic stress at point A, the soil unit wieght is 18 kN/m3. 6 m 1.6 m 3 m •A 1.5 m PLAN 6 m Vertical load 50 kN/m2 3 m SECTION Select one: O a. 24 kN/m2 o b. 44 kN/m2 OC 54 kN/m2 o d. 45 kN/m2
Given is the 200mm X 400 mm rectangular beam below. 9 kN 7.50 kN/m 400 mm 1.50 kNm A 1.50m 7.50m 200 mm R2 Figure 1 Compute the flerural stress developed in MPa at a distance 1.5Om from the left end at the underside of the beam??
For the dam retaining water as shown, find (A) the factor of safety against sliding if µ=0.48, (B) the factor of safety against overturning and (C) the stress intensity at the base of the dam. The foundation soil is permeable; assume hydrostatic uplift varies from full hydrostatic head at the heel of the dam to zero at the toe. Use unit weight of concrete equal to 23.5kN/m?. 3 m 4 m 8 m 3 m to W.S 12 m 14 m 3 m 3 m O O
Extra Question: If the Dead load in the slab shown is 24 KN/m^3, determine the end support reaction at beam BE. A E B S1 (200 mm) 1.5 m Option 1 a) 16.1 KN Ob) 17.1 KN Oc) 18.1 KN Od) 19.1 KN S2 (150 mm thick) 4.0 m S1 (200 mm) 1.5 m > 4.5m
Calculation Example Foundation 3 m x 4.5 m 4.5 m Load 2025 kN -3 m -1.5 m- Determine the increasing of vertical stress below point A, B, and C at the depth of 3 Flan m. Section
4:50, 100, and 150 kN point loads are applied at Points A, B, and C, respectively, on the ground surface as seen in the figure. Compute the vertical stress increment under Point D down to the depth z=20 m. Use Vertical stress Increment under corner of rectangular footing? 150kn 7.5m 50kn 2m™ (Plane view) 3m 5m 100kn
What is the boundary shearing stress (in KPa) of a rectangular channel having dimensions of b = 2.89 m and d = 4.97 m? Channel slope is = 0.056. Round off to two decimal places.
For the loaded area shown below, determine the increase in vertical stress (4p) at 5 ft below points B and C at the depth of the pipe, which is z = 5 feet below the footing, and 3 feet a way from its edge. The footing has a UDL , q = 1800 lb/ft2. 1,800 B. A 5t 4ft 5t 2 B 10 t 3 ft 10 ft 3 ft PLAN VIEW SECTION