A metal block 30 cm square and 25 cm deep is floated on a body of liquid which consist of 20 cm layer of water above the layer of mercury. The block weighs 18 840 N/m. If a downward vertical force 1 100 N is applied is applied to the center to the center of this block, determine the location of the top edge of metal block before and after the vertical force is applied.

A metal block 30 cm square and 25 cm deep is floated on a body of liquid which consist of 20 cm layer of water above the layer of mercury. The block weighs 18 840 N/m. If a downward vertical force 1 100 N is applied is applied to the center to the center of this block, determine the location of the top edge of metal block before and after the vertical force is applied.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

JB TIDE blocks The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 1500 N and a force F= 500 N. It is made from a material which has a yield strength of 60 MPa, Determine the factor of safety at points A and B using the Von-Mises Theory. 100 mm 50 mm F 2 of 6
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the %3D figure. Determine the total resultant force acting on the gate and the location of the center of pressure. 6 ft 3ft VAVAVAVAVA Ib f Unit weight of the liquid (y) Value of hbar (h) Arca of the rectangular gate (A) Hydrostatic Force (F) Vahe of (Igx) Vahue of ybar (9) Location of the Hydro. Force measured from the water surface of the gate inclined (yel Ib ft ***answer Hydrostatic Force Fon the box below: Answer: 1311.03 The correct answer is: 1022.1
3. Two cylinders A and B weighs respectively Weven 150KN and 200KN. What is the tensile stress developed in EVEN: the string DE if the diameter of the string is 16mm? Diameter of cylinder A=40mm Diameter of cylinder B-100mm L=120mm and CD-200mm E 62° B
Plate with 0.13 m wide and 0.25 m length passes thru oil with layer 3.5 mm and 5 mm thick. Both surface sides of the plate touch the oil that has a viscosity of u=0.038 Ns/m^2. Determine the force required (in newton) to move the plate at speed of 5 mm/s
Problem 6.2: The aluminum rod ABC (E=10.1x10 psi) (Figure 6.19), which consists of two cylindrical portions AB and BC, is to be replaced with a cylindrical steel rod DE (E=29x10° psi) of the same overall length. Determine the minimum required diameter d of the steel rod if its vertical deformation 28 kips 28 kips D 12 in. 15 in. is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the B steel rod is not to exceed 24 ksi. –2.25 in. ed 18 in. E Figure 6.19
A welded steel cylindrical drum made of a 10-mm plate has an internal diameter of 1.20 m & height of 4m. Compute the change in length that would be caused by an internal pressure of 1.5 MPa. Assume that Poisson's ratio is 0.30 andE = 200 GPa. * thickness, t= 10 mm 1.20 m O 0.270 mm O 0.360 mm O 0.108 mm O 0.459 mm.
An aluminum block (SG=2.5) has a dimension of 0.29 m x 0.29 m x h meters. It is floating in mercury (SG=13.6) and the submerged height of the block is 0.85 m. Determine the weight (kN) of the block.
A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN. The compression of the rod is 1.35 mm, and its diameter becomes 30.015 mm. Determine the Poisson's ratio v of the material. Assume the material does not yield. A 0.33 0.30 0.28 D 0.25
1. Given that the value of P on the figure below is equal to 15 kN which is applied to the centroidal axis of each segment of the rod which is made up of aluminum, bronze and steel which are rigidly connected. Determine the stress in each material in the rod. Steel A=300 mm2 Bronze Aluminum A=400 mm2 A=600 mm2 2P ЗР 4P P 3m+ 5 m 4 m-
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in bronze bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 144.21 102.49 341.33 54.56
In a rotating cylinder test, the inner cylinder is of diameter 0.2 m and the outer cylinder of diameter 0.205 m contains the liquid up to a height of 0.3 m. The clearance at the bottom of the two cylinders is 5 mm. When the outer cylinder is rotated at a speed of 400 r.p.m, the torsion meter attached to the inner cylinder show the value of torque equal to 5886 Nm. Determine the viscosity of liquid.
A cube contracts in volume by 0.05% when acted upon by normal uniform pressure of 2x 106 N/m? on all sides. The bulk modulus of its material is (а) 400 MPа (4000 MPa (d) 40000 MPa (b) 40 MPа