A multifluid container is connected to a U-tube, as shown in the figure. For the given specific gravitles and fluid column heights. determine the gage pressure at A. Also determine the height of a mercury column that would create the same pressure at A. The column heighth of oil is 86 cm. The specific gravitles are 1.26 for glycerin and 0.90 for oll. We take the standard density of water to be Pw=1000 kg/m³ and the specific gravity of mercury to be 13.6.

A multifluid container is connected to a U-tube, as shown in the figure. For the given specific gravitles and fluid column heights. determine the gage pressure at A. Also determine the height of a mercury column that would create the same pressure at A. The column heighth of oil is 86 cm. The specific gravitles are 1.26 for glycerin and 0.90 for oll. We take the standard density of water to be Pw=1000 kg/m³ and the specific gravity of mercury to be 13.6.

Name: A multifluid container is connected to a U-tube, as shown in the figu
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A multifluid container is connected to a U-tube, as shown in the figure. For the given specific gravitles and fluid column heights.determine the gage pressure at A. Also determine the height of a mercury column that would create the same pressure at

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

An inverted differential manometer is connected to two pipes A and B which convey water. The fluid in manometer is oil of SG= 0.8. For the manometer reading shown in the figure, find the pressure difference between A and B. X 30 cm 20 30 OIL OF Sp. gr. 0.8 -X
A B с OIL WATER 1.0M 0.5m In the tank open to the atm. shown in the figure below, there is on oil layer 1 meter high on a 0.5 meter high water layer. Since pont & is in the Middle of paints A and C. calculate the pressures at points A, B, C, D in Kla. (Density of water 1000 kg/m³, density of oil 800 kg/m³)
and (B) the gauge pressure at a depth of 2.50 m in the 5. A mercury U-tube barometer is used to measure atmospheric pressure. The top end of the tube is closed off and evacuated so that the pressure there is zero. The other end is open to the atmosphere. Consider the U-tube barometer in the figure, what is the height h of the mercury column if the pressure is 1 atm?
In the figure, pressure gauge A shows 1.5 kPa (gauge). Fluids are at 20 ° C. Determine the elevation z in meters of the level at which to find the liquids in tubes B and C.
a drum has gasoline s.g=0.9, with oil s.g=0.8 and sea water s.g=1.03. the depth of the liquid is 0.8m, 0.5m, and 1.0 for gasoline, oil and sea water.1. find absolute pressure at depth 1.2m 2.find the depth at 1.8m 3. find the force F at depth 2.1m when diameter of drum is 0.5m
A 10000 litre water tank is placed on a building roof and filled to capacity. The empty tank has a mass of 550kg. It is supported on 4 feet, each of which is a 300 x 300 mm steel plate. What is the pressure exerted by each plate, in Pa? (Round your answer to 2 significant figures)
The tank of an air compressor has a volume of 2m3 and is filled with air at a temperature of 40 degrees C. If agauge pressure on the tank reads 7.5 bars,what is themass of the air in the tank?
A U-tube manometer is connected to a closed tank as shown. The air pressure in the tank is 0.25 psi and the liquid in the tank is oil (SG=0.6) . The pressure at point A is 1 psi. a. Determine the depth z (in feet) of oil in the tank. b. Determine the differential reading, h (in feet), on the manometer.
1. Find the density of an oil filled in the liquid column as shown in figure. Given that absolute pressure at the bottom is 500 kPa, atmosphere pressure is 1.0132 bar. where X=4m; Y = 4m, Z=1.25m. (Enter only the values in the boxes by referring to the unit given in the bracket. Do not send the hand written answer sheets to my mail) water oil Y Mercury The density of the oil = (unit in kg/m³) =
Figure 1 shows a fairly large U-tube manometer containing water (density p= 1000.0 kg.m³3) and oil (density p=900.0 kg.m³). The left-hand side opening is sealed with a rubber stopper. The height of the oil column is h₂ cm. The height of the water column above the water/oil boundary is h₁ = 20.00 cm. The external pressure is given by Pout = 100.00 kPa. (i) Calculate the absolute pressure at the bottom of the oil column. (ii) Calculate pin, the absolute pressure directly under the rubber stopper. Express your answers to at least 4 significant figures in SI units. Pout Pin h₁ U water oil h₂ Figure 1: Stoppered U-tube manometer containing water & oil
An 8-in.-diameter piston is located within a cylinder that is connected to a 0.5-in.-diameter inclined-tube manometer as shown in the figure. The fluid in the cylinder and the manometer is oil (specific weight = 57 Ib/ft3). When a weight, W, is placed on the top of the cylinder, the fluid level in the manometer tube rises from point (1) to (2). How heavy (in Ib) is the weight? Assume that the change in position of the piston is negligible. W 6 in. (2) (1) Piston Oil 30°
Consider the tank shown (Figure 2), where the specific weight of the water is yw = 9800 N/m³ and the specific weight of molasses is ym = 1.4x104 N/m³. What is the pressure at the bottom of the tank if h1 = 3.4 m and h2 = 3.7 m. Water h2 Molasses