A pipeline having a diameter of 250 mm has a rate of flow of 0.30 m³/sec. from point 1 to 2, with 2 lower than 1. A gate valve is connected at a point 3 near point 2. The elevation of point 2 is 100 m. O Compute the elevation of 1 when the gate valve at 3 is closed and the difference in pressure P2 - P1 = 78 КРа. ® Compute the head loss from 1 to 2 when the gate valve at 3 is open and the difference in pressure Ри- Р2%3D 160 kРа. 3 Compute the length of pipe from 1 to 2 if f = 0.020.

A pipeline having a diameter of 250 mm has a rate of flow of 0.30 m³/sec. from point 1 to 2, with 2 lower than 1. A gate valve is connected at a point 3 near point 2. The elevation of point 2 is 100 m. O Compute the elevation of 1 when the gate valve at 3 is closed and the difference in pressure P2 - P1 = 78 КРа. ® Compute the head loss from 1 to 2 when the gate valve at 3 is open and the difference in pressure Ри- Р2%3D 160 kРа. 3 Compute the length of pipe from 1 to 2 if f = 0.020.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the discharge at pipeline 2 in lit/sec assuming f=0.02 for all pipes. 700 m 450mm diam. 0.86m3/s Pipe 2 800 m 400mm diam. Pipe 3 700 m 500mm diam. O 200 100 250
(a) Figure Q2.7 shows an inverted U-tube manometer with oil of density 800kg/m3 above thepipe liquid, which is water. The pipeline is horizontal. What is the value of (P1-P2)? (b) If the manometer readings are the same but the oil is replaced by air, what is (P1-P2) now? 280 mm Figure Q2.7 P₁ 北 P₂ 430 mm
QI/ Water flows from the reservoir on the left to the reservoir on the right at a rate of 0.45 ms. The formula for - Ekevation? the head losses in the pipes is h - 0.02 L: D 2g What elevation in the left reservoir is required to produce this flow? Also carefully sketch the HGL and the EGL for the system. Note: Assume the head-loss formula can be used for the smaller pipe as wel as for the Elevation 34 m 80 m 90 m D, =0.344 m A, -0.1 m D,= 0.486 m A- 02 m larger pipe. Q2/ A horizontal pipe carries cooling water at 10°C for a thermal power plant. what is the pressure in the pipe at L= 2000 m? The head loss in the pipe is 0.02(L/D)V + Eerhm- 0n -D02m 28 Detn where Lis the length of the pipe from the reservoir to the point in question, V is the mean velocity in the pipe, and Elvation =m L-2000m (2. Dis the diameter of the pipe. The pipe diameter is 20 cm and the rate of flow is 0.06 mls, Q3/ For the parallel-pipe system of L-250 D-3 in Fig. each pipe is cast iron, and the pressure drop p -…
5 Two reservoirs are connected by a pipeline, The diameter of the pipe is (0.5 m and the difference in levels of the two reservoirs is 12.5 m. The total length of the pipe is 1000 m. The velocity of flow in the pipe taking into account both major and minor losses will be [Take, friction factor f-0.04 and g 10 m/sec] (a) 1.75 m/s (c) 4.5 m/s (b) 3.2 m/s (d) 0.5 m/s
Two tanks A and B have 80 m diffenence in water levels, and are connected by a pipe 0.3 m diameter and 8 km long with 0.002 friction coefficient. The pipe is tapped at its mid point to leak out 35 1/s flow rate. Determine the leaving tank А? discharge Find the discharge entering tank B? Coefficient (Tank Exit) = 0.5 %3D Coefficient (Tank Entry) = 1 %3D ha %3D A he 80 m Q1
Pipes 1, 2 and 4 are connected in series with pipes 2 & 3 parallel to each other.Pipelines Diameter Length Friction Factor1 350mm 2500m 0.022 400mm 4000 m 0.023 300mm 2000 m 0.024 450mm 2500 m 0.02If the discharge of pipeline 2 is 0.05 m^3/s,1. Compute the rate of discharge of pipeline 32. Compute the rate of discharge of pipeline 43. Compute the total headloss of the pipe system
Pipelines 1, 2 and 3 are connected with parallel to each other with pipeline 1 having a diam. of 450 mm, 600 m long, pipeline 2, 400 mm diam., 800 m long and pipeline 3, 500 mm diam., 700 m long. the 3 pipes carries a combined discharge of 0.86 cum/sec. Assuming f = 0.02 for all pipes. -Compute the discharge of pipeline 1. -Compute the discharge of pipeline 2. -Compute the discharge of pipeline 3.
Q2: A is 4500 m length-gas flow line, and B is 2000 m length-liquid flow line (0.1 m diameter) both are connected with left side of 2500 m in length C-pipeline (0.15 m). If the pressure at A-pipeline inlet = 2400 kPa, pressure at C-pipeline out let = 2000 kPa, liquid flow rate = 0.009 m³/s, Gas Oil Ratio = 40 m³/m², PL 680 kg/m³, p=0.922 kg/m³, gas flowing temperature-300 K, base temperature-288 K, base pressure 101.3 kPa, Z-0.9, gas gravity 9.4x10-3 Pa.s, calculate the 0.6, gas viscosity-0.015x10³ Pa.s, and liquid viscosity diameter of gas pipeline and inlet pressure of liquid pipeline? Assume all pipes are flat and horizontal. =
In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000 ft long and 15-inch in diameter. The pipe is commercial steel with roughness 0.00015 ft. Water temperature is 50°F (kinematic viscosity is 1.41 x 105 ft?/s), and the total discharge is to be 4 ft /s? Use g = 32.2 ft/s?. Determine: The velocity, friction factor, and flow rate of water in pipes 1 and 2. (1) A B
Fluid flows at the rate of 0.272 m/s in a 925 mm diameter pipeline 588 m. long. Specific gravity of fluid is 0.57. Neglecting minor losses and f= 0.012. Compute the head loss in m. A. 2.684 B. 0.594 C. 3.92 D. 0.064 A system of pipes consists of a 10 inches pipe 2,500 ft. long and an 8 inches pipe 3,600 ft. Long. If Q = 650 gpm and f = 0.013, find the equivaient diameter of the pipes when the pipes are in series. A. 0.811 ft B. 0.911 ft C. 0.711 ft D. 1.11 ft ft
3. A pump is used to transport water at the rate of 0.075 m³/s from a reservoir 20 m above the pump to a free discharge 35 m above the pump. The pressure on the intake side of the pump is 150 kPa and the pressure on the discharge side is 450 kPa. All pipes are commercial steel of 15 cm inner diameter. Determine (a) The head supplied by the pump (b) The total head loss between the pump discharge and point of free discharge. Z₁=20 m 1 P₂ = 150 kPa 2 面 3 D=15 cm A P3=450 kPa 4 Free Discharge Z4 = 35 m
Pipeline AB connects two reservoirs. The difference in elevation between the two reservoirs is 33 ft. The pipeline consists of an upstream section, D1 section, D2 end with a sudden reduction of area. Assume the water temperature is 68°F. Compute the discharge сарacity. = 30 in. and L1 21 in. and L2 = 3,500 ft. The pipes are concrete (smooth) and are connected end to 5,000 ft; and a downstream