A simple rotating loop between two curved pole faces connected to a battery and a resistor through a switch has the following characteristics : Radius of the loop, r = 8 m, length of the loop, l = 1 m, Resistance = 0.38 ohm, flux density B = 0.22 T and Voltage at the terminals of the loop. Vr = 126 V. What would be the strarting current in the loop if the switch is initially closed? Question 4 Answer a. 0 A b. 2652.63 A c. 331.58 A d. 331.58 A

A simple rotating loop between two curved pole faces connected to a battery and a resistor through a switch has the following characteristics : Radius of the loop, r = 8 m, length of the loop, l = 1 m, Resistance = 0.38 ohm, flux density B = 0.22 T and Voltage at the terminals of the loop. Vr = 126 V. What would be the strarting current in the loop if the switch is initially closed? Question 4 Answer a. 0 A b. 2652.63 A c. 331.58 A d. 331.58 A

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Similar questions

Look carefully at the figure and answer the following questions. For your answers choose between on the right, on the left and it is zero; there are no more options. (a) When the switch is “open” i. Where does the current flow in the battery? ii. Where is the magnetic flux going in the bar on the left? iii. Where does the magnetic flux go in the bar on the right? iv. Where does the current flow in the resistor?
How can the polarity of an electromagnet be determined if the direction of current flow is known? 2. Define the following terms: 3. flux density 4. Permeability 5. Reluctance 6. Saturation Unit 13 Magnetic Induction 7. Name three factors that determine the amount of induced voltage in a coil. 8. What is the effect on induced voltage of adding more turns of wire to a coil? 9. Into how many time constants is an exponential curve divided? 10. Each time constant of an exponential curve is equal to what percentage of the maximum amount of charge? 11. An inductor has an inductance of 0.025 H and a wire resistance of 3 . How long will it take the current to reach its full Ohm's law value? Unit 15 Alternating Current . 12 What is the most common type of AC waveform? 13 How many degrees are there in one complete sine wave? 14 At what angle does the voltage reach its maximum negative value on a sine wave? 15 A sine wave…
A current in a 250 turn coil is 2.25A, wound in a core that has a reluctance of 12,000 AT/Wb. What is the resulting flux density (in Tesla), if the area of the core is 8cm²?
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron).
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm², and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (ur = 800 for iron).
11. There is 900 mA of current through a wire with 40 turns. What is the reluctance of the circuit if the flux is 400Wb? 14,400 At/Wb B 1,440 At/Wb Ⓒ9,000 At/Wb O90,000 At/Wb Answer: Option O Explanation: No answer description is available. Let's discuss.
Problem 1A core with a coil has 240 turns, to generate a flux ø of 0.008482 weber, how much should the current i1 be and what will its direction be? Relative permeabilities: metal 1 of 250 and metal 2 of 375. Core depth 25cm
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm?, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron). Figure 1
The reluctance of a non-magnetic circuit is 14 units. How much flux will be set up if surrounded by a coil 620 turns carrying a current of 3.6 Ampere? Draw the diagram
The reluctance of a non-magnetic circuit is 15 units. How much flux will be set up if surrounded by a coil 560 turns carrying a current of 3.2 Ampere? Draw the diagram for the question
1.Consider the magnetic core below.All dimensions are shown on the figure. The core is made up of legs with 2 different cross-sectional areas.The depth of core is 10cm.The relative permeability of the core is 2000. The current in the magnetising coil is 1 A. The number of turns of the coil is 2000.Calculate: (i)the reluctances and draw the magnetic circuit (ii)the flux in the core (iii)Flux densities B and field intensities H in legs having different cross-sectional areas. (iv)Verify Ampere's Law. Depth: 10 cm I=1A 20cm 2000 Turns 65cm 15cm 15cm 50cm 15cm ndo un of
Question 3 A two-legged core is shown in Figure 3. The winding on the left leg of the core has N1 = 400 turns, and the winding on the right has N2 = 300 turns. The coils are wound in the directions shown in the figure. If the dimensions are as shown, then what flux would be produced by currents i = 0.5 A and iz = 0.75 A? Assume ur = 1000 and constant. 15 em- +15 em 50 em 15 cm 50 em 400 turms 300 turns N2 15 cm Core depth = 15 em Figure 3