A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (Qu) to the boiler. c. Calculate Wpump- d. Calculate |WNet|. e. Determine the thermal efficiency (n.) 6 MРа, 2 550 °C Boiler 6 MPа w, (turbine) mass flow rate (m): 22 kg/s Turbine Turbine efficiency (isentropic): 89 % w, (pump) 3 4 Condenser 50 kPa 50 kPa Working fluid: water

A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (Qu) to the boiler. c. Calculate Wpump- d. Calculate |WNet|. e. Determine the thermal efficiency (n.) 6 MРа, 2 550 °C Boiler 6 MPа w, (turbine) mass flow rate (m): 22 kg/s Turbine Turbine efficiency (isentropic): 89 % w, (pump) 3 4 Condenser 50 kPa 50 kPa Working fluid: water

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
Homework-2 Compute the themal e fficiency of an ideal Ran kine cycle for which the steam leavea the boiler as Saturated Vapor at 30 bars. The turbine-outlet Conditions is Be1 bar. Determine the mass floo rate of the steam in kg/hr, net Power output of the cycle is 50000 Sehematic ond given data are: 1f the kw. The TI= 5002 P 3०bars %3D 9in (saturated) vapour 30 bars 2 PR =0-1 bar 4 Pa=30 bas o-1 bar +4 Tout 3 (Saturated liquid) Wp ( Simple Ideal Power cycle) (T.S. diagram e)
A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (QH) to the boiler. c. Calculate Wpump- d. Calculate |Wnetl. e. Determine the thermal efficiency (n) 6 MPа, 550 °C Boiler 6 MPa w, (turbine) |mass flow rate (m): 22 kg/s Turbine Turbine efficiency (isentropic): 89 % w, (pump) 3 4 Condenser 50 КРa 50 kPa Working fluid: water
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Ideal turbine work (KW). Ans.____________________________ Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Pump work in KW. Ans.___________________________
28. A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specifie volume is 12.6 and final specific volume is 3.25 If the inlet suction lirfe is 4" I.D. and the discharge line is 2.5" I.D. Determine ft-lb (a.) The change in flow energy between the boundaries in- min Ib (b.) the mass flow rate in and min (c.) the change in velocity in fps.
H.W2:-A) The bore and stroke of an internal combustion engine working on Otto cycle are (17 cm) and (30 cm) respectively. If the total volume is (8.825 cm3),find the air standard efficiency. Take X=1.4
Given : Given :take P1 = 10 KPa Turbine entry conditions = 16 MPa and 600 oC(Degrees Celsius)Turbine output=5 MPaPhase state saturated water at the heat exchanger outlet and heat exchanger efficiency 85%Required power for district heating = 1100 kWTurbine power= 5500 kWQuestion: What is the value of my ??? Give answe upto 5 decimal points ( only correct is needed )
1.4 A diesel engine operating an air standard diesel cycle has 20cm bore and 30cm stroke. the clearance volume is 420cm3. if the fuel is injected at 5% of the stroke, find the air standard efficiency. 1.5 Develop an expression for the thermal efficiency of the air-standard diesel cycle as a function of the compression ratio r. = V1V2 and the expansion ratio r, = V4 / V3. Assume the working fluid is an ideal gas, and the volume effect of moles of gas generated is small relative to the effect of heating from combustion. %3D
A standard oil-gas horizontal separator, the gas stream has flow rate around 3.5MMscfd, the amount of oil flow rate 870 bbl./day, the working pressure 1000 psia under temperature 31°C, it's full to a third liquid capacity and the amount of mass flow rate=77161.81b/hr. If the settling size of this separator is (36*10'), assess if it's possible to use this size in well with all these conditions then summarize the final result, calculate the mass velocity in this separator Fraction factor 1.2, compressibility factor 0.86, Gas sizing constant 0.19 Density of liquid and gas (5.2,3.1) lb./cuft respectively.
You have been asked to help with the low-pressure compressor (LPC) design for a turbofan engine with a bypass ratio of 8.4. The preliminary cycle design calls for the LPC to produce a pressure ratio of 9.4 with the following operating conditions and constraints. .Inlet Conditions TO2 Poz Core Air Mass Flowrate (kg/s) (K) (kPa) 282 24.6 47.0 Design Constraints Maximum Polytropic Efficiency 94.1% Maximum Stage Pr 1.55 Estimate the minimum number of stages required for this LPC. Then assuming the 1st stage of the LPC operates at the maximum allowable pressure ratio, determine the stagnation temperature exiting the 1st stage, and the stage's adiabatic efficiency. Also determine the power (W) required to operate the full LPC (not just 1st stage). Finally, what would be the percent change in the required power if the polytropic efficiency was only 90.0%.
1. Using the Steam Tables, determine the heat absorbed by the boiler (KW) and Wsf when subcooled water at pressure = 5 Mpaa (subcooled by 64 deg C measured at the boiler inlet), is superheated to 100 degrees SH at the same pressure. Flow rate is at 10 cubic meters per minute. Ans.: a) Qa = b)Wsf= Hint: Use v at compressed water temp. at boiler inlet to convert to mass flow rate. Process is isobaric (Constant Pressure, where Q=m x AH).
i need some one explian the TS digram Rankine Cycle