A student wants to standardize their thiosulfate solution with KIO3. They needed 17.97 mL of S203²- solution to neutralize 19.0 mL of 0.0200 M KIO3. Based on these results, what is the concentration of the thiosulfate solution? Again, your equations are: 2 S2032- + 12 → KIO3 + 5 KI + 6 HCI → S40,2- + 21- 3 1, + 6 KCI + 3 H20

A student wants to standardize their thiosulfate solution with KIO3. They needed 17.97 mL of S203²- solution to neutralize 19.0 mL of 0.0200 M KIO3. Based on these results, what is the concentration of the thiosulfate solution? Again, your equations are: 2 S2032- + 12 → KIO3 + 5 KI + 6 HCI → S40,2- + 21- 3 1, + 6 KCI + 3 H20

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter3: Chemical Reactions

Section: Chapter Questions

Problem 92QRT: You mix 25.0 mL of 0.234-M FeCl3 solution with 42.5 mL of 0.453-M NaOH. Calculate the maximum mass,...

See similar textbooks

Similar questions

One method for determining the purity of aspirin (C9H8O4) is to hydrolyze it with NaOH solution and then to titrate the remaining NaOH. The reaction of aspirin with NaOH is as follows: A sample of aspirin with a mass of 1.427 g was boiled in 50.00 mL of 0.500 M NaOH. After the solution was cooled, it took 31.92 mL of 0.289 M HCl to titrate the excess NaOH. Calculate the purity of the aspirin. What indicator should be used for this titration? Why?
Suppose 50.0 mL of 0.250 M CoCl2 solution is added to 25.0 mL of 0.350 M NiCl2 solution. Calculate the concentration, in moles per liter, of each of the ions present after mixing. Assume that the volumes are additive.
Consider an experiment in which two burets, Y and Z, are simultaneously draining into a beaker that initially contained 275.0 mL of 0.300 M HCl. Buret Y contains 0.150 M NaOH and buret Z contains 0.250 M KOH. The stoichiometric point in the titration is reached 60.65 minutes after Y and Z were started simultaneously. The total volume in the beaker at the stoichiometric point is 655 mL. Calculate the flow rates of burets Y and Z. Assume the flow rates remain constant during the experiment.
You mix 25.0 mL of 0.234-M FeCl3 solution with 42.5 mL of 0.453-M NaOH. Calculate the maximum mass, in grams, of Fe(OH)3 that will precipitate. Determine which reactant is in excess. Calculate the concentration of the excess reactant remaining in solution after the maximum mass of Fe(OH)3 has precipitated.
Two students titrate different samples of the same solution of HCl using 0.100 M NaOH solution and phenolphthalein indicator (Figure 4.12). The first student pipets 20.0 mL of the HCl solution into a flask, adds 20 mL of distilled water and a few drops of phenolphthalein solution, and titrates until a lasting pink color appears. The second student pipets 20.0 mL of the HCl solution into a flask, adds 60 mL of distilled water and a few drops of phenolphthalein solution, and titrates to the first lasting pink color. Each student correctly calculates the molarity of an HCl solution. What will the second students result be? (a) four times less than the first students result (b) four times greater than the first students result (c) two times less than the first students result (d) two times greater than the first students result (e) the same as the first students result
In the spectroscopic analysis of many substances, a series of standard solutions of known concentration are measured to generate a calibration curve. How would you prepare standard solutions containing 10.0, 25.0, 50.0, 75.0, and 100. ppm of copper from a commercially produced 1000.0-ppm solution? Assume each solution has a final volume of 100.0 mL. (See Exercise 123 for definitions.)
Titration of a 20.0-mL sample of acid rain required 1.7 mL of 0.08 11 M NaOH to reach the end point. If we assume that the acidity of the rain is due to the presence of sulfuric acid, what was the concentration of sulfuric acid in this sample of rain?
A mountain lake that is 4.0 km × 6.0 km with an average depth of 75 m has an H+(aq) concentration of 1.3 × 10−6 M. Calculate the mass of calcium carbonate that would have to be added to the lake to change the H+(aq) concentration to 6.3 × 10−8 M. Assume that all the carbonate is converted to carbon dioxide, which bubbles out of the solution.