(a) The Varnes system divides slope failures into five types. Briefly explain all FIVE types of slope failure with relevant sketch. (b) As a geotechnical engineer, you are required to determine the stability of slope. Propose relevant soil tests and calculation required to determine the factor of safety.

(a) The Varnes system divides slope failures into five types. Briefly explain all FIVE types of slope failure with relevant sketch. (b) As a geotechnical engineer, you are required to determine the stability of slope. Propose relevant soil tests and calculation required to determine the factor of safety.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Explain very briefly the following:1. What types of slope failure are common in soils?  2. What factors provoke slope failures?  3. What is an infinite slope failure?  4. What methods of analysis are used to estimate the factor of safety of a slope?  5. How does seepage affect the stability of slopes?  6. Difference between Culmann’s method and Swedish circle method for slope stability analysis
(b) The road embankment will be constructed on soft soil. Since the short-term stabilityis more critical than the long-term stability, you, as a geotechnical engineer, arerequired to propose and discuss the related laboratory testing to be performed inorder to analyse the short-term stability of road embankments ?
describe the main differences between short term and long term stability analysis jn soil mechanics. why is it important to consider both types of analysis in geotechnical engineering?
a)As an engineer and based on information provided, you are required to identify the possible technical cause of theslopefailure. Based on the photo provided and field test, identify the type of slope failure aswell as the possible type of soils.
Q1. Geologists investigating a landslide surveyed the elevation of a hillside and found it to be 872 m at the bottom and 991 m at the top. The survey points were horizontally separated by 465 m. How steep is this hillside as a percent grade if 45 degrees is a 100 percent grade? percent grade = ........... % Q2. Enter your answer in scientific notation. The discharge (Q) of a stream is the velocity (v) times the cross-sectional area (A): Q = vA. What is the discharge of a stream with a velocity of 2.1 m/s and a cross-sectional area of 54.2 m2? Q = ........ × 102 m^3/s
Discuss five limitations of soil erosion formula(RUSLE)
Please answer the problem attached image below. Assume: Seismic Zone 4 and Soil Profile Type: SD ,I=1.0 , Na=1.5 , Nv=2.0, Ca=0.44Na, Cv=0.64Nv, Z=0.4 Using NSCP 2015. Earthquake engineering subject.
Explain about the Noncircular slippage plane for slope stability analysis, Janbu method.
Which of the following statements apply for slope stability (select all correct answers)? a)The driving forces acting along a slip surface increase as the soil unit weight below the slip surface increases and vice versa. b)A FoS equal to one is generally considered as safe in engineering practice when considering permanent actions. c)For coarse-grained soils, the FoS decreases as the soil friction angle decreases and vice versa. d)For non-saturated coarse-grained soils, the soil strength mobilised along a slip surface increases as the slip inclination angle decreases and vice versa. e)Planar slip surfaces are more likely to occur in saturated homogeneous clays in undrained condition.
1. Discuss spatial slope stability. 2. Examine the landslide characteristics and spatial distribution 3. Examine earthquake intensity 4. Landslide susceptibility mapping 5. Investigate community knowledge on pre-disposing factors to landslides CR [] AP [] CR [] AP [ AP [
You are required to analyse a slope stability problem using the Swedish method for failure along the slip surface as shown in the figure below. The slope is inclined at an angle of 30° to the horizontal and has a height of 10 m. The ground water table (GWT) is located at a depth of 5.1 m below the crest. It goes along the slope and reaches at the toe level as shown in the figure. Soil investigation revealed that the site consists of a layer of silty clay overlying a layer of sand. Assume c = (40 + 2x) kPa and ϕ = 10° for the silty clay, and c = 0 and ϕ = (30 + x)° for the sand layer; where x is the last digit of your student ID (e.g., if your student ID is 5746189, x = 9). All slices have equal width (b = 2.89 m) and the slices are numbered 1‒6 from left to right. The coordinates of the midpoint of the bases (M , M , M , M , M , M ) of the slices are shown on the right side of the figure. The weights of slices 1‒6 are as follows (in kN/m): W1 = 53.5, W2 = 141.3, W3 = 199.6, W4= 224.8,…
A geotechnical engineer is evaluating the stability of the slope shown in Figure 1. This evaluation is considering the potential for a shear failure along the shear surface shown. The soil has φ’= 30o and no cohesive strength. a). Compute the effective shear strength at Point A along this surface when the groundwater table is at level B, then compute the new shear strength if the groundwater table rises to level C. The unit weight of the soil is 120 lb/ft3 above the groundwater table and 123 lb/ft3 below b). If the shear stress at point A is 2000 psf, what are the factors of safety against sliding at water level B and C? Hint: use effective stress and assume the failure surface at point A is horizontal.