.A thin cylinder of inner radius 500 mmand thickness 10 mm subjected to aninternalpressure of 5MPа. Theaverage circumferential (hoop) stressin MPa is

Given, Radius of cylinder = R = 500 mm Thickness of cylinder = t = 10 mm Internal pressure = P = 5…

Answered: A thin cylinder of inner radius 500 mm…

A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.1P: A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer...

See similar textbooks

Related questions

Q: A steel rod of 20 mm diameter passes centrally through a copper tube of external diameter 40 mm and…

Q: A thin hollow spherical container has a diameter 1 m and a thickness of 4 mm is subjected to an…

Q: A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: given data;load=mg=25*9.81=245.25Nlimiting stress σ=27.24kpa=27240Pa=27240N/m2cross sectional…

Q: An L-shaped bracket lying in a horizontal plane supports a load F = 1kN. The bracket has a hollow…

A: Write the given information.

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner radiu…

Q: For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the…

A: Sddd

Q: Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 1850…

A: GIVEN :- b1=85mmb2=130mmb3=60mmd=28mmP=1850N

Q: A piping tube with an outside diameter of 50 mm and wall thickness of 5 mm is used as a compression…

Q: A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5…

A: Given data: p=5 MPar=500 mmt=10 mm Need to determine the average circumferential (hoop) stress.

Q: Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure…

A: Data given - P = 9 MPa r = 150 mm Or d = 2 × r = 2 × 150 = 300 mm t = 9 mm

Q: Q3 - A thin-walled cylindrical vessel has an internal diameter of 1m and a thickness of 10 mm…

A: pressure:- Pressure is defined as the physical force exerted on an object. The force applied is…

Q: 8. A solid steel bar of diameter d, = M mm has a hole of diameter d2 = N mm drilled through it. A…

Q: A thin copper tube, 14 mm internal diameter and 0,5 mm wall thickness has closed ends and rotates at…

Q: determine the tensile stress induced in the bolt.

A: For solution refer below images.

Q: Problem No. 3. The compound shaft has the following properties: G in both Segment 1 Segment 1 pipe…

Q: 5. Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in.…

Q: A solid steel bar with a diameter of 50 mm is subjected to three forces as shown in the figure,…

A: In the given problem, the main stresses will be developed at point B due to 1200N force which will…

Q: A thin hollow sphere of radius 300 mm and thickness 2.5 m is subjected to an internal pressure.…

A: Thin spherical shell is given Tensile stress in sphere = σ = 360 kPa Radius of sphere = r = 300 mm…

Q: 3.5 m r= 0.6e-0.08y² y 0.6 m

Q: |F 2F a 3F| b a

Q: A steel wire 30 ft long, hanging vertically, supports a load of 500 lb. Neglecting the weight of the…

Q: 4. A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37.5mm…

A: Find the stress at point C and D and also find the value of force Q.

Q: It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN) mm…

Q: A central horizontal section of a hook is a symmetrical trapezium of inner width =67.5mm and of…

A: Given:Inner width,bi=67.5 mmOuter width,bo=22.5 mmP=37.5 KNInner radius,Ri=52.5 mmh=90 mmOuter…

Q: A 2-meter concrete column (Ec=30 GPa) is reinforced with six 25-mm diameter steel bars (Es=200 GPa)…

Q: Figure 5 shows a thick cylinder of 50 mm internal radius and 115 mm outer radius is subjected to an…

A: Given data Inner radius = 50 mmOuter radius = 115 mmInternal Pressure =60 MN/m2External Pressure =…

Q: 7) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 40 mm. The…

A: Given Data: Diameter of cylinder, d=550 mm Thickness, t=40 mm

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

A: The formula for the hoop stress can be expressed as,

Q: 4. A thin cylinder of inner radius 500 mm and thickness 10 mm is subjected to an internal pressure…

Q: 1. A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A: Given data:t=20 mmD=450mmL=2mσl=140 MPaσc=60 MPa

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: For the Given system P = 9 kips Q = 5 kips R = 20 kips S = 30 kips stress limit in (1) = 19 ksi…

Q: It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN) mm…

Q: Calculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and…

A: Given Data: The permissible stress in Bronze cable is, σ1=76000 kPa. The permissible stress in…

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The…

A: Given data, σl=155MPa σc=55 MPa Outer Diameter do= 500 mm= 0.5 m Inside diameter d= 500-10= 490…

Q: The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical…

Q: A thick cylinder of 150 mm outside radius and 100 mm inside radius is subjected to an external…

Q: subjected to uniform uniaxial tension of 95 MPa. A large uniform plate containing a rivet hole is…

Q: A steam turbine rotor is 160 mm diameter below the blade ring and 25 mm thick. The turbine is…

A: A steam turbine rotor has a diameter of 160 mm below the blade ring and is 25 mm thick.The turbine…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

Q: It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN) mm…

Q: 5: An aluminum rod (E-70 GPa and v=0.25) is inserted into a hollow steel tube (E=210 Gra and…

A: Given data:- P= 200KN D=40 mm Di =50 mm t = 10 mm

Q: A steel column of hollow circular cross section shown in Figure is supported on a circular steel…

Q: 5. Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in.…

A: Given Allowable stress in rod AB = 3400 psi Outer diameter = d1 Inner diameter = d1 - 0.125…

Q: Determine the thickness of a steel air receiver with 30 in. diameter and pressure load of 120 psi,…

Q: A steel bar has a uniform cross sectional area of 300mm². Calculate the stress at member AB 1.6m…

Q: 1. Draw a diagram of the longitudinal force 2. Draw a diagram of normal stresses 3. Determine…

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner…

A: solutionwe have given in the question.outer radius (r0)=260mminner radius (ri)=55mminterval pressure…

Q: A steel cylindrical vessel is subjected to a pressure of 21 MPa. Its outer diameter is 4.6 m and its…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

.A thin cylinder of inner radius 500 mm
and thickness 10 mm subjected to an
internal
pressure of 5
MPа. The
average circumferential (hoop) stress
in MPa is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A cast aluminum cylinder of a portable hydraulic riveter is d 210mm in diameter. The pressure of the fluid is p 16N/mm2 by gauge. Determine suitable thickness of the cylinder wall assuming that the yield point stress is A 444MPA and factor of safety of B 6.Calculate the tangential and radial stresses at the inner, middle radius and outer surfaces.
P= 200 lbs |=2" T 250 in-Ibs Qt. DRAW STRESS STATES いITH A SQLARE ECEMENT エN xY AXES Label with stress values Q2 DRAW MOHR'S CIRCLE AT A Q3.CALCULATE PRINCIPAL STRESSES AND DRAW THE PLANE FoR ri$ a IN THE SCHEHATIC Draw element rotated to principal planes and label with stress values and rotation angle
Problem 7 A 12-inches square steel bearing plate lies betw een an 8-inches diam eterw ooden postand a concete footing as show n in Fig.P-110.Determ ine the m axim um value of the bad P if the stress in w ood is lim ited to 1800 psiand that in conarete to 650 psi 8 in Bearing Plate 12 in 12 in Figure P-110
(b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is approximately 3.2N/mm. Design the studs also for the cylinder cover. Assume the allowable hoop stress =42 N/mm' for cast iron; the allowable tensile stress for material of studs =63 N/mm?
A cast aluminum cylinder of a portable hydraulic riveter is d mm in diameter. The pressure of the fluid is p N/mm2 by gauge. Determine suitable thickness of the cylinder wall assuming that the yield point stress is A MPa and factor of safety of B .Calculate the tangential and radial stresses at the inner, middle radius and outer surfaces. Let D = 208 mm P = 15.8 N/mm2 Yield stress = 442 N/mm2 %3D Factor safety = 6.2
Q3: (a) describe the location and function of the following: \i. Gudgeon pin ii. Rod shank ii.Large end (b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is approximately 3.2N/mm. Design the studs also for the cylinder cover. Assume the allowable hoop stress =42 N/mm' for cast iron; the allowable tensile stress for material of studs =63 N/mm?
A cast ALuminum cylinder o f a portable hdrauli c riveter is 208 mm in ddiameter The pressure. of The luid petermine Sui table thickness is 15,8 NImm2 by gauge. f the Cylinder wall assuming that the ield Point stress 442 N/mm2 And factor of safety of 6.2 Calculate. the tangential and radial stresses middle radius and at the inner outer surfa ce.
The cylinder pressure vessel has an inner radius of 1.25 m and a wall thickness of15 mm. It is made from steel plates that are welded along the 45oseam. The vesselis internally pressurized by 10 Mpa. a. Is it a thin or thick wall? b. What are the general state of stresses for this problem? c. Is it plane stress problem? d. Using Mohr’s circle, find out the principle stresses. e. What would be the shear stress values associated with the principle stresses? f. Determine the normal and shear stress components along this seam, usinganalytical equation, and then show the normal stress and shear stress componentsin your Mohr’s circle. ONLY A,B & C PLEASE
Answer the ff correctly. The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.