An aluminum hollow shaft 200 mm outside diameter, 100 mm inside diameter and 500 mm length from lathe chuck is to be face turned at the end. Its end face is finished at a rotational speed of 400 rpm using a feed rate of 0.25 mm/rev. The side cutting edge angle or lead angle of the tool is 300 . How much cutting time and maximum power is needed to finish the facing operation with a 4 mm depth of cut. What is likely to be a perpendicularity error in this operation? Specific cutting energy = 0.025 W/ mm3 /min and E = 50 kN/mm2

An aluminum hollow shaft 200 mm outside diameter, 100 mm inside diameter and 500 mm length from lathe chuck is to be face turned at the end. Its end face is finished at a rotational speed of 400 rpm using a feed rate of 0.25 mm/rev. The side cutting edge angle or lead angle of the tool is 300 . How much cutting time and maximum power is needed to finish the facing operation with a 4 mm depth of cut. What is likely to be a perpendicularity error in this operation? Specific cutting energy = 0.025 W/ mm3 /min and E = 50 kN/mm2

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.3: Machining Operations On The Lathe

Problem 5RQ: Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a...

See similar textbooks

Similar questions

Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
17) A50-mm-dia endmill cuts 6061 aluminum with 30% tool engagement at a depth of 6 mm. The tool rotates at 200 rpm and is feeding at 250 mm/min. There are 2 teeth set at a rake angle of 10°. a. Calculate the required power of cutting. b. Determine the spindle torque. c. Determine the cutting force on each tooth. d. If the thrust force is measured to be 350N, estimate the tool-chip interface friction coefficient. How could you physically verify your power estimate?
How much machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by turning using a carbide insert. If the approach length and over run length is = 5 mm, Cutting speed is 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm D
A drilling operation is performed to create a through hole on a steel plate that is 20 mm thick. Cutting speed = 0.4 m/s, and feed = 0.20 mm/rev. The 18-mm-diameter twist drill has a point angle of 120°. Determine the following once the drill reaches full diameter: a. the machining time and, b. the metal removal rate Equation used Tm TD₂L fv
The face milling cutter of D = 200 mm used to cut a block which is 200 mm H, 1=480 mm, if f- 0.7 mm/rev is used and the overrun of the cutter is 12 mm and cutting speed 320 mm/min. Calculate the machining time. Cuttin
Exercises 4 1. A 30 mm diameter mild steel bar is being turned at a spindle speed of 8 rev/s, on a multi-tool centre lathe having eight tools in operation. The feed is 0-3 mm/rev, the specific cutting pressure/tool is 2 000N/mm and the total power consumed for the operation is 14 kW. If the depth of cut is to be kept the same for each tool, calculate the depth of cut/tool in mm.
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes (a) Find number of passes to finish the entire turning operation ( (b) The actual length of the turning operation in mm ('
Calculate the machining time to drill four 20 mm diameter holes and one 50 mm diameter central hole in the flange as shown below. Take cutting speed 20 m/min, feed for 20 mm drill 0.2 mm/rev, and for 50 mm drill feed is 0.6 mm/rev, the point angle is 120°? VIVER 20xA 200 D100 SYLON 50
Exercises 4 1. A 30 mm diameter mild steel bar is being turned at a spindle speed of 8 rev/s, on a multi-tool centre lathe having eight tools in operation. The feed is 0-3 mm/rev, the specific cutting pressure/tool is 2 000N/mm2 and the total power consumed for the operation is 14 kW. If the depth of cut is to be kept the same for each tool, calculate the depth of cut/tool in mm. (Ans. 3-8 mm)
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=