Combustion of a fuel sample in a bomb calorimeter increases the temperature of the entire system by 5.10 °C if the calorimeter contains 1700 g of water, but only by 4.00 °C if the calorimeter contains 2200 g of water. What is the heat capacity of the dry bomb calorimeter assembly? Assume that the specific heat capacity of water is 4.18 J g–1 °C–1.

Combustion of a fuel sample in a bomb calorimeter increases the temperature of the entire system by 5.10 °C if the calorimeter contains 1700 g of water, but only by 4.00 °C if the calorimeter contains 2200 g of water. What is the heat capacity of the dry bomb calorimeter assembly? Assume that the specific heat capacity of water is 4.18 J g–1 °C–1.

Curren'S Math For Meds: Dosages & Sol

11th Edition

ISBN:9781305143531

Author:CURREN

Publisher:CURREN

Chapter10: Reconstitution Of Powdered Drugs

Section: Chapter Questions

Problem 42SST

See similar textbooks

Similar questions

Sugar solution is being heated to 83 o C in a jacketed pan made from stainless steel, 1.6 mm thick. Heat is supplied by condensing steam at 200 kPa gauge in the jacket. Calculate the rate of heat transfer if the surface heat transfer coefficients for condensing steam and sugar solution are 12000 J/m2-s-oC and 3000 J/m2-s-oC, respectively. Thermal conductivity for the stainless steel is 21 J/m-s-oC and the surface area of the pan is 1.4 m 2 .
How many grams of NaOH would you need to make 3,982 mL of a 3 M NAOH solution (m.w. = 40.00 g/mol)? Report your answer in the requested units to the nearest 2 decimal places (Example "40.02"). Do not report the units in your answer; enter the numbers only. It is recommended that you do not round between calculation steps.
Solution A is 20 degrees celsius, Solution B is 80 degrees celsius (both are the same kind of solution). The goal is to make a 50 degree celsius solution; How much of solution A do you need (starting with 100g of solution B)? (cp=4.184 J/g C)
A clinical technician finds that the activity of a sodium-24 sample is 1088 cpm. What will be the activity of the sample 90. h later if the half-life of sodium-24 is 15 h?
A mixture containing only KCl and NaBr is analyzed by the Mohr Method. A 0.3172-g sample is dissolved in 50 mL water and titrated to the Ag2CrO4 endpoint, requiring 36.85 mL of 0.1120 M AgNO3. A blank titration requires 0.71 mL of titrant to reach the same endpoint. Report the % (w/w) KCl and NaBr in the sample. [Ans . 84.41 % (w /w); 17.59 % (w /w)]
75 g of impure sodium hydroxide is added to 250 cm3 of water. 10 cm3 of this impure solution is neutralized by 13,5 cm3 of HNO3concentration 0,2 mol.dm–3.Calculate the percentage purity of the sodium hydroxide.
A sample of steel weighing 2.00 g is analyzed for Cr (AW 52.0). The Cr is oxidized into chromate with alkaline permanganate and the excess permanganate is destroyed. A certain volume of 0.120 M FeSO4 is added to the acid solution and the excess is titrated with 0.0220 M KMnO4, requiring 31.0 mL. If the sample contained 0.50 % Cr, what volume (in mL) of FeSO4 was added?
You just made a 1.5M permanganate solution. What concentration is your potassium permanganate solution in percent? "K: 39.10 g/mole" "Mn: 54.94 g/mole" "O: 16 g/mole" "MW of KMnO4 is 158.04 g/mole" O a. 0.24% Ob. 20.1% O c. 15.8% O d. 23.7% O e. 2%
Twenty observations on etch uniformity on silicon wafers are taken during a qualification experiment for a plasma etcher. The data are as follows: Etch Uniformity 5.34 6.65 4.76 5.98 7.25 6.00 7.55 5.54 5.62 6.21 5.97 7.35 5.44 4.39 4.98 5.25 6.35 4.61 6.00 5.32 (a) Discuss the normality assumption and its role in this problem. (b) Check normality by constructing a normal probability plot. What are your conclusions?
The material to be heated is in a long, cylindrical tube, and is viscous enough that any flow inside the tube can be ignored, i.e. the heating is by conduction alone). Also, consider the glass of the tube to be very thin so its thermal resistance can be ignored. The tube diameter is 1 cm and the properties of the material are the same those of water, given by 0.64 W/m*K, 1000 kg/m3, and 4180 J/kg*K, for thermal conductivity, density, and specific heat, respectively. The water bath temperature is 65 °C, and the initial temperature of the material is 27 °C. Without the agitation of the water bath, the heat transfer coefficient can be considered to be 128 W/m2*K. Considering the tube to be a long cylinder, how long does it take for the coldest point to heat up to a temperature corresponding to 99% of the total possible temperature increase? If the surrounding how water is agitated using a stirrer, leading to a considerably large surface heat transfer coefficient, how long does it…
A chemist is performing a precipitation titration on a 1.00 L sample containing an unknown concentration of the cadmium ion, Cd2+. If it takes 24.52 mL of a 0.250 M solution of Na2CO3 to reach the end point, calculate the concentration of the cadmium ion?
A medication order for a patient weighing 145 lbs calls for 0.25 mg of Drug B per kilogram body weight to be added to 1000mL of 5% dextrose injection. If Drug B is to be obtained from a reconstituted injection that contains 50mg/10mL, how many milliliters should be added to dextrose injection?