Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal andvertical planes at the point are S,- 28 MPaS,-60 MPa, and Sy- 26 MPa.(a) Draw Mohr's drde for this state of stress(b) Determine the principal stresses and the maodmum in-plane shear stress acting at the point.() Show these stresses on an appropriate sketch (eg, see Fig 1215 or Fig 12.16).(d) Determine the absolute madmum shear stress at the pointSyS,Answer:(a) Draw Mohr's Circle for this state of stressMPa(b) Op1-MPaMPaTar inplane() Show these stresses on an appropriatesketch (eg, see Fie 12.15 or Fig 1216)MPa(d) Ts ma

Answered: Image /qna-images/answer/06b3d060-52d8-406c-ae8b-6bef910ece17.jpg

Consider a point in a structural member that is subjected to plane stress. Normal ar vertical planes at the point are S,- 28 MPaS,-60 MPa, and Sy- 26 MPa. (a) Draw Mohr's drde for this state of stress (b) Determine the principal stresses and the madmum in-plane shear stress acting= () Show these stresses on an appropriate sketch (eg, see Fie 1215 or Fig 12.16). (d) Determine the absolute madmum shear stress at the point

Consider a point in a structural member that is subjected to plane stress. Normal ar vertical planes at the point are S,- 28 MPaS,-60 MPa, and Sy- 26 MPa. (a) Draw Mohr's drde for this state of stress (b) Determine the principal stresses and the madmum in-plane shear stress acting= () Show these stresses on an appropriate sketch (eg, see Fie 1215 or Fig 12.16). (d) Determine the absolute madmum shear stress at the point

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At a point in a stressed material, the stress combination acting on a plane is a 90 kPa compressive stress and a 30 kPa shear stress, while on a perpendicular plane, the stress combination is 30 kPa compression and 30 kPa shear. Use the Mohr’s circle for this stress analysis. (a) Determine the values of the major and minor principal stresses. (b) Determine the angle between the major principal plane and the plane where the 90 kPa compressive stress acts.
Problem 4 : For the shown Mohr circle: (a) What is the state of stress at the reference point A. Sketch the element at A. (b) Determine the principal normal stresses and their orientation. Show the results on a properly oriented element (c) Determine maximum in-plane shear stress and its orientation. Show the results on a properly oriented element A 20 40 60 80 100 Ở, ksi 20 40 -60
A stat of stress is specified in figure by using Mohr's circle determine the normal and shearing GPI. GP2 stresses on (a) the principal plane, (b) the planes of maximum shearing stress and sketch the ERST resulting elements. 400 MPa 250 MPa 560 MPa
element in each case. Question 3. Determine the principal stresses, the maximum in plane shear stress, and average normal stress. Specify the orientation of the Question 4. The state of stress at a point in a member is shown on the plane AB. element. Determine the stress components acting on the inclined 200 MPa 500 MPa 40 MP1 350 MPa 65 MPa
Problem 2: The stresses shown act at a point on the free surface off a stressed body. a) Determine the principal stresses and the maximum in-plane shear stress acting at the point b) Show these stresses in an appropriate sketch. c) Determine the normal stresses on and ot and the shear stress Tnt that act on the rotated stress element. 53 MPa 16 MPa 47 MPa 35⁰
A cube (E = 200GPA) is experiencing stress from all directions. Along the x-direction, there is a compressive stress of 50MP.. Along the y-direction, there is a tensile stress of 80MPA. Along the z-direction, there is a tensile stress of 100MPA. Solve the strain along the x-axis if the Poisson's Ratio is 0.3. O -0.000455 O -0.000520 O -0.000325 O -0.000416
PROBLEM 7.63 For the state of stress shown it is known that the normal and shearing stresses are directed as shown and that o, =98 MPa, ơ, = 63 MPa, and omin = 35 MPa. . Determine (a) the orientation of the principal planes, (b) the principal stress Omaxs (c) the maximum in-plane shearing stress.
Strength For the state of plane stress shown, determine the largest value of o, for which the maximum in plane shear stress is equal to or less than 75 MPa. After you determine the value, draw Mohr circle for the case
Find the value of maximum principal stress if maximum shear stress is 60 MPa and minimum principal stress is 50 MPa
Determine the effective stress (i.e. grain pressure) σ'v0 acting in the plane of consideration
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S, = 8.0 ksi, S, = 10.5 ksi, and Sxy = 8.0 ksi. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point. Sy Sxy S.
Determine the magnitude of the shear stress (in units of MPa) when the state of stress is oriented 45 degrees from the element shown (aligned with line AB).