Design the circuit below to obtain a dc emitter current Ie=1.2 mA, using a power supply Vcc= 12V. The design assumes a very large B value first. After determining all resistor values, recalculate Ig for B=110. (Hìnt: As a rule of thumb, use Vce=-Vcc and IcRc=-Vcc and the 3 3 voltage-divider current is 0.1IE). Voc Ans. R = Rc R2= Rc= RE = R IE (B=110)= R,

Design the circuit below to obtain a dc emitter current Ie=1.2 mA, using a power supply Vcc= 12V. The design assumes a very large B value first. After determining all resistor values, recalculate Ig for B=110. (Hìnt: As a rule of thumb, use Vce=-Vcc and IcRc=-Vcc and the 3 3 voltage-divider current is 0.1IE). Voc Ans. R = Rc R2= Rc= RE = R IE (B=110)= R,

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

All field-effect transistors are unipolar rather than bipolar devices. That is, the main current through them is comprised either of through an N-type semiconductor * ..... .....
Question: 8. With the emitter bias shown, a reasonable assumption for troubleshooting work is that the VcC a. base voltage =+1 V +15 V b. emitter voltage = +5 V RC 3.9 k2 c. emitter voltage =-1 V d. collector voltage = Vcc RB 68 kQ %3D RE 7.5 kQ VEE -15 V
04:- Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE = 10 V. Use standard valued 5% resistors and draw a schematic diagram of your design. (10 points)
For the circuit given in figure below draw the collector characteristic curves for IB = 50,150 and 250 micro amperes on the same graph
For positive half of the signal below, what is the peak output value of the circuit? NOTE: use silicon diode ?
A 4.7 zener diode is connected to the base resistor. The left side of the resistor sits at about 12V. The right side of the biasing resistor is connected to the Zener and npn transistor. The Zener bias is 5mA. The base current needed is 80uA. What is the appropriate resistor for this circuit? (In kohms) I
3. Write down which transistor structure each curve characteristic belongs to in the figure. Ip -VGS -VGS +VGs (c) VGS (b) (a)
4 For the transistor shown in below figure, Calculate the value of R, that will just make the transistor work as closed switch. Hence Bpc= 80, VBE = 0.7V, VCE(sat) = 0.2V, Vcc= 12V, Rc= 2.7KN. la) Calculate the In and I.. Vcc RB Rc |b) Calculate Rp- B'
c. For the circuit shown in Figure, determine lc and VCB. Assume the transistor to be made of Silicon. Ic RE=1.6 kn Rc=1.1 kn EE=8 V Vcc= 20 v
Measurements taken with an E-MOSFET indicate that when VGS=+4V, ID=8mA, and when VGS=+6V, ID=32mA. Determine the value of k.
Q-1) Given a SCR that is in TO-3 package. In data sheet, Rejc is 2.5 °C/W, ReSA is 2.5 °C/W, and Recs is 1 °C/W. How much power will the SCR be able to dissipate and not exceed a junction temperature of 200°C if the ambient temperature is 40°C?
two applications for a Bipolar Junction Transistor and talk about one in detail