First, design a beam and obtain its moment and bending stress diagrams using the software BeamBoy. The beam has the following specifications: · Length 8 m · Simply supported at 0 m and 6 m · There is a uniform distributed load of 10 kN/m between the two supports · There is a point load of 20 kN located at the end of the beam · When using BeamBoy, select the cross-section W12 × 96

First, design a beam and obtain its moment and bending stress diagrams using the software BeamBoy. The beam has the following specifications: · Length 8 m · Simply supported at 0 m and 6 m · There is a uniform distributed load of 10 kN/m between the two supports · There is a point load of 20 kN located at the end of the beam · When using BeamBoy, select the cross-section W12 × 96

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam shown in the figure below is subject to a moment of M = 17 kN.m as illustrated. Calculate the maximum tensile and compressive bending stresses. |-75 mm - - 12 mm B 12 mm 12 mm 75 mm 250 mm D 12 mm
The beam shown is made of a nylon for which the allowable stress is 24MPa in tension and 31MPa in compression. Determine the largest couple M that can be applied to the beam. 24 mm 60 mm 30 mm 80 mm
Q2/ The beam shown is made of a nylon for which the allowable stress is 24 MPa in tension and 30 MPa in compression. Determine the largest couple M that can be applied to the beam. 40 mm 15 mm M d = 30 mm 20 mm
9. A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the figure. The vertical load is always twice of the horizontal load. The collapse load P required for the development of a beam mechanism is P B A Mp K+ 2P 2Mp L с Mp D L
A double tee cross section is used for the beam shown below. Assume the following lengths and loads: a = 14 ft b = 7 ft c = 9 ft P = 8000 lb Q= = 3000 lb The moment of inertia of the cross section is l₂ = 110 in.4. Determine the magnitude (i.e., the absolute value) of the maximum tensile bending stress in the beam. Answer: a Omax (Tension) = i P V B b C psi C q x TT ↑ 3.2 in. 5.8 in.
A cantilever beam of length 6 m has an additional support at a distance of 2 m from its free end as shown in Figure 4. It has the cross-sectional dimensions with height h=300 mm, inside height h₁ =250 mm, width b= 150 mm, and inside width b₁=100 mm. It is made of an elastic perfectly plastic material having tensile and compressive yield stress of oy = 250 MPa. Determine the yield moment My of the beam Determine the plastic moment Mp of the beam ✓ By using force method and selecting the vertical reaction at C to be redundant, draw shear and bending diagrams using the graphical method. -Determine the minimum value of W at which collapse occurs B/2W C 77 2m 2m 2m C b₁
NEED ANSWER ASAP!! A so-called "trapeze bar" in a hospital room provides a means for patients to exercise while in bed (see figure). The bar is 2.1m long and has a cross section in the shape of a regular octagon. The design load is 1.6kN applied at the midpoint of the bar, and the allowable bending stress is 240 MPa. Determine the minimum height h of the bar. Round to one decimal place. (Assume that the ends of the bar are simply supported and that the weight of the bar is negligible.) hmin=___mm
Consider the truss shown in (Figure 1). Suppose that F = 30 kN Figure A 3m 3m < 1 of 1 ▼ Determine the force in the member CD of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case tension. FCD- Value Submit Part B HA Part C Request Answer Determine the force in the member CB of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCB- Value Submit Request Answer HÀ Submit Part D FDA- Value HA Determine the force in the member DA of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive…
A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm.Parameter Description Value UnitsL - Beam length 250 mma - Width of the flange 80 mmd - Height of the web 75 mmσ - Yield stress 250 MPaYou are tasked with ensuring the beam can withstand the applied loading. To do this you must:a) Calculate the centroid for the given cross-section. Your value of ?ത should be measured fromthe bottom of the section. Determine an expression for Q (statical moment of area) for thegiven shape. The expression(s) for Q should be in terms of the variable, y, measured from thebottom of the section. b) Create a graph of the shear and bending stresses at the fixed support (B) over the crosssection. The stresses should be plotted as a function of y, measured from the bottom of thesection.
Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
A steel beam (E = 208GPa) has square cross-section (edge = 40mm) and is constrained and loaded as in the figure below: a) Identify and name all the supports and draw the Free Body Diagram of the beam b) Write all the relevant equilibrium equations and find all the reaction forces c) Draw the shear and bending moment diagrams d) What is the average shear stress in the middle of the beam? If the vertical load is removed, what is the final length of the beam after deformation? 250kN 2m 20kN 3m Figure Q1 20kN → 2m Ha Ji
If the beam is subjected to an internal moment of M = 30 kN.m, determine the maximum bending stress in the beam. The beam is made from A992 steel. Sketch the bending stress distribution on the cross section. 50 mm 50 mm 15 mm 10 mm M 150 mm 15 mm