Food Processing Industry System Details: Piping diameter 50 mm, length 100 meters, used for transporting milk at a flow rate of 50 litres/min. Chemical Manufacturing System Details: Piping diameter 25 mm, length 250 meters, used for chemical solvents at a flow rate of 15 litres/min. Water Treatment Facilities System Details: Piping diameter 300 mm, length 1000 meters, used for moving water at a flow rate of 1000 litres/min through sedimentation and filtration processes. a) Examine the characteristics of fluid flow in these three industrial piping systems.

Food Processing Industry System Details: Piping diameter 50 mm, length 100 meters, used for transporting milk at a flow rate of 50 litres/min. Chemical Manufacturing System Details: Piping diameter 25 mm, length 250 meters, used for chemical solvents at a flow rate of 15 litres/min. Water Treatment Facilities System Details: Piping diameter 300 mm, length 1000 meters, used for moving water at a flow rate of 1000 litres/min through sedimentation and filtration processes. a) Examine the characteristics of fluid flow in these three industrial piping systems.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

2. [R] A pumped supply system will be used to transport water at 15 °C between two reservoirs with a total head difference of 50 m. The pipes of the system consist of a 600 m long pipe on the suction side of the pump with diameter 200 mm and absolute roughness 0.2 mm; and a 2 km long pipe on the delivery side of the pump with diameter 150 mm and absolute roughness of also 0.2 mm. The suction and delivery pipes have total secondary loss coefficients of 80 and 200 respectively. The pump impeller eye is located 4 m below the water level in the suction reservoir. The required flowrate in the system is 40 L/s. Determine the following for the system. a) The working point of the pump to deliver the required flowrate. {191 m, 40 L/s} b) The classification of the flow in the suction and delivery pipes based the zones defined on the Moody diagram. (both transitional turbulent) c) The minimum input power required by the pump if the pump efficiency is assumed to be 75%. (100 kW}
Air ducts in buildings are vital for ventilation. Assume that through a duct of 1 ft diameter, 3000 cubic feet of air is refreshed every hour. • What is the average velocity of air in the duct? • Assume that the inner surface of the duct is smooth, what is the pressure drop over 100 ft of this duct? Air's density = 1.225 kg/m3; Air's viscosity = 0.018 cp
(20) Question 2 A hydraulic motor is directly coupled to the drum of a belt conveyor. The drum diameter is 0.75 m, the conveyor belt moves at a speed of 3 m/s and the motor must transfer a torque of 995 Nm to the drum. Assume the pressure drop across the motor is 22 MPa and that the motor has an overall and mechanical efficiency of 0.92 and 0.96 respectively. Determine the displacement volume of the motor, the flow rate required in litres per second and the hydraulic power supplied to the motor.
The following are general features of Spring & Diaphragm EXCEPT А. Simple mechanism В. Cost effective C. Based on air pressure Require electric supply D.
A groundwater well with produces 80 m/hr. and has a hydraulic conductivity of 20 m/d. Calculate the following: a. The length of the screen b. The diameter of the delivery pipe. c. The velocity head and the friction losses in the delivery pipe. d. What is the required power of the pump if the abstraction efficiency was 70%? Assume the following: The percentage of the opening in the screen is 17%, the entrance velocity is 1.55 cm/sec, the diameter of the screen is 30 cm, water velocity in the tube is 2.2 m/sec. Assume any missing data.
Homework Parts A-C and label them QUESTION: In Tinyland, houses are less than a foot high! The rainfall is laminar! The drainpipe in the figure is only 2 mm in diameter. Part (A) - When the gutter is full, what is the rate of draining? Part (B) - The gutter is designed for a sudden rainstorm of up to 4 mm per hour. For this condition, what is the maximum roof area that can be drained successfully Part (C) What is Red? Neglect minor losses. HINT : 4mm PER HOUR ***
2. A turbine is used to produce 2700 hp by expanding the water between points 1 and 2. Water flow rate, static pressures and pipe diameters are given. Calculate the power lost in between point one and two. Note that the static pressure at point 2 is given in vacuum. (SGH =13.6) P1 = 60 psi Q = 150 ft³/s D = 3 ft Section (1) Turbine 10 ft P2 10-in. Hg %3D vacuum D2 = 4 ft Section (2)
Each project should be presented in written and oral forms. A written individual report should contain a summary, introduction, short literature review, objectives, methodology, results and discussion and conclusion. Project 1 A vortex tube is a mechanical-thermal device that separates a compressed flow of air (or any inert gas) into hot and cold streams and has no mechanical moving parts. Cold Air Compressed Air Supply Vortex Spin Chamber (2 cold outlet f = 0.25 P₁ = 100 kPa d. e. Develop the main equations f. Estimate the COP with and without the vortex tube. https://blog.exair.com/2018/10/31/the-theory-of-the-vortex-tube/ a. Start by solving using the simple problem (problem 1) described below. b. Derive the basic equations allowing its performance evaluation. c. Develop an EES model and conduct an analysis on the thermal performance of this device. Consider three working fluids. Consider the integration of the vortex tube with a refrigeration system. Control Valve Hot Air 6 Problem…
Cell culture media is flowing through a cylindrical tube at a volumetric flow rate of 12 ml/s. The tube has a diameter of 0.8 cm and length of 12cm. Assume the viscosity of the media is 1.2 cP (0.0012 Pa s). a. What is the shear rate at the wall of the tube ? b. What is the shear rate at the centerline of the tube ? c. What is the shear stress at the wall of the tube ?
The hydraulic conductivity of an aquifer is 0.005 cm/sec, the hydraulic gradient is 0.02, and the porosity is 0.2. What is the specific discharge, q, in this aquifer? Calculate the velocity at which dissolved salt could move through this aquifer. Assume the aquifer is 5 meters thick . What it is its transmissivity? Transmissivity T = Kb aquifer thickness. What is the discharge per unit of distance perpendicular to the groundwater flow?
A Large wind turbine has blade span diameters of 110 m. It sits high off the ground where the average wind speed is 7 m/s. Assume the air density to be 1.25 kg/m3, and the efficiency of the wind turbine, its generator and its electric grid synchronization device is 26%. What is the average electric power that this turbine can output to the grid? a. Sketch the problem. b.Draw lines identifying the control volume, or control mass. c.Identify the states with numbers, letters, or descriptions such as “in” and “out”. d.Write down the knowns and unknowns. e.Identify what is being asked for. f.State all assumptions.
In the hydroelectric power plant whose cross-section is given, the flow rate of Q=33.045 m^3/sec is transmitted to the power plant through a D=1.6 meter diameter penstock. Ignoring friction losses; a) Find the internal pipe pressure at point 2 ( at the below ). b) Find the resultant force (F) and its direction (O) that the water exerts on the fixation mass. c) Calculate the electrical power generated in the plant. (Pwater= 1 ton/m^3, Ywater= 9.81 kN/m^3, g=9.81m/s^2, Beta= 45 degree