If the specific gravity of the oil SG=0.8 what should be the value of h so that the net horizontal hydrostatic force on the cylinder with diameter of D be equal to zero? D/2 water D O a) h=0.75D h = 1.25D h=1.5D d) h=1.667D h=? oil

Q: Suppose that a = 2.5 in. and b = 4.5 in. (Figure 1) Figure y 2 in.--2 in- in. a 1 of 1 Part A…

A:

Q: 7. It is known that 5,000 automobile trips are generated in a large residential area from 3:00 PM to…

A: Number of automobile trips generated, n = 5000 For a logit model, Coefficients for commercial space…

Q: Two plates are connected by a bolt as shown in the figure. What is the shear stress on the bolt? D…

A:

Q: 1. A 5 m simply supported beam is loaded with a 10 kN-m concentrated moment placed 3.5m from the…

A: The length of beam = 5 m  Concentrated moment= 10 kN-m placed at 3.5 m from left support  The…

Q: 2. Determine the moments at each joint of the frame shown in Fig. a. El is constant. Using moment…

A: To find the final end moment in the given frame. It can be understood from the eccentric load that…

Q: The deflection and slope at C will be (take El = 12000 kNm²) 24 kN A I m 60 kNm 1 m B

A:

Q: 12. Determine the reactions at the supports, using moment distribution method 2m 40 kN 2m t 21 m 2…

A: Given : Required : Support reactions using moment distribution method

Q: n the field of architecture, what exactly is meant by the term "pattern"? How can these three…

A: The field of architecture ensures the products as well as the planning and design of the…

Q: A 20’ high slope has an angle of 31⁰ and is composed of sandy clay (SC). The soil has a unit weight…

A: To determine the factor of safety using the Cousins chart, first need to calculate the shear…

Q: Suppose that a = 2.5 in. and b = 4.5 in. (Figure 1) igure y -2 in.--2 in.- 1 of 1 Determine the…

A: a=2.5in b=4.5in Let 1 denotes rectangle and 2 denotes circle

Q: 5 3 7 8 Table below shows the chainage (length), cut and fill end areas Earthwork Calculations…

A: The chainage and the cut and fill areas are given.     To determine the volume of the fill in cubic…

Q: Situation 3: Determine the force in each member of the truss if W = 100 kg. State if the member is…

A: Truss is given as shown in the figure. W= 100 kg

Q: How can virtue ethics inform the practice of architecture, and what virtues are essential for…

A: A philosophical perspective known as virtue ethics emphasises the formation of moral character and…

Q: Problem 03.142 Hollow A hollow member having the cross section shown is formed from sheet metal of…

A:

Q: 8 kN 1 m -2.5 m DRAW M N T DIAGRAMS 8 kN -2.5 m 16 kN/m -4 m 4 kN/m -2 m

A:

Q: A truss is subjected to the loading condition shown in the diagram. You are required to determine:…

A:

Q: Look for the large, dark colored building that is located slightly north and west of the Mandalay…

A: Mandalay Bay Hotel/Casino  has a more traditional rectangular shape and stands at a height of 43…

Q: An unconfined compression test was conducted on an undisturbed of clay. The sample has a diameter of…

A:

Q: In figure, a tank 1.5 m by 1.5 m horizontal section and 3 m high with two orifices (C= 0.60) both 10…

A: Diameter of orifice= 0.1 m Find: The time in minutes to take out a flow unit no flow is left through…

Q: Example: The annual precipitation at station X and the average annual precipitation at 15…

A: The annual precipitation at station X is given  The average annual precipitation at 15 surrounding…

Q: he data pertaining to a stream-gauging site are given below. The rating equation of the current…

A: For the last and first section using equation average width = W¯=w1+W22)22w1 For the rest of the…

Q: What is the maximum absolute shear for the following beam and load group? Use L = 19, a = 3, b = 3,…

A:

Q: Find the maximum point live load (P) can be loaded on the end of the cantilever beam shown below. If…

A:

Q: A trapezoidal channel with brick lining has a bottom slope of 0.001 and a base width of 4 m, and the…

A:

Q: A reinforced concrete beam has a width of 300 mm and an effective depth of 450 mm. The beam is…

A: Given: Required : Balanced steel ratio Depth of compression stress block Nominal moment capacity

Q: Steel, fy (main bars) = 415 Mpa Steel, fyt (ties) = 275 Mpa 1. Determine the minimum spacing “a”,…

A:

Q: If two closely coiled helical springs A & B with the mean diameter of spring A is half of that of…

A: Two closely coiled helical springs A & B- Equal numer of active coils & Same wire…

Q: A spill occurred at a septic tank and an adjacent property owner concerned about the spill could…

A: Well location = 100 feet away from point of spill hydraulic conductivity k = 0.0164 ft/sec slope =…

Q: 10. For the figure shown below, calculate the moments and reactions at the supports using three…

A: To find the Moments and reactions at the supports in the given beam using the three Moment…

Q: The influence line is for V40 = shear just left of 40'. A load of 0.5 kip/ft is placed from O' to…

A:

Q: 2. An intersection has a 2-timing stage signal with the movements allowed in each timing stage,…

A: A intersection of 2-timing stage signal is given Lost time = 3 seconds v/c ratio = 0.85 Total lost…

Q: Figure 1 F 三 7m

A:

Q: Q2) A screen is installed at a channel in the head of water treatment plant. The channel is of Im…

A: Design criteria for screens are as follows Design parameter Manually cleaned Mechanically cleaned…

Q: If two closely coiled helical springs A & B with the mean diameter of spring A is half of that of…

A: If two closely coiled helical springs A & BEqual numer of active coilsSame wire diameter,Same…

Q: 2 kip/ft B A 10 kips C 4 ft 10 ft 8 ft D E

A:

Q: 1. Two plates 400mm x 20mm is to be connected using PJP groove weld con that is 15mm deep. Using…

A:

Q: Determine the shear and moment diagrams of the beam loaded as shown.

A: Calculation For SF and BM as shown beam Drawing of SFD , BMD

Q: GIRDER B1-2 & B1-4 12.629 KN 26.23 KN 6.741 kN/m GIRDER B1-7, B1-2, & B1-9 2(12.621) KN 3.5 m 48.851…

A: Calculate for the deflection for both of these figures. Note:  Since it is not mentioned where to…

Q: A sewage treatment plant uses the activated sludge process in its biological treatment unit with…

A: A primary sedimentation tank data is given as shown below and it has been asked to calculate F/M…

Q: EXAMPLE 12.6 Glorswork 3 Determine (approximately) the reactions at the base of the columns of the…

A:

Q: 11.18 A long, flat steel bar 4 in. wide and 3 in. thick is reduced in width to 3 in. There are…

A: Applied load (P)=12000lb D=4in d=3 in Thickness (t)=3/8 in

Q: A 85 kN/m B 2.7 m 2.2 m 65 kN/m ↓↓↓↓↓↓↓ C 3.2 m D 1.5 m E Draw the Shear and Moment Diagram of the…

A: Given : Required : Shear and moment diagram using shear and moment equations

Q: 12-1. An L2 steel strap having a thickness of 0.125 in. and a width of 2 in. is bent into a circular…

A: L2 steel strap thickness=0.125 in width= 2in Radius of circular arc=600in To find Maximum bending…

Q: haccp plan of hazard analysis of set yogurt Hazard Number Identified Hazard & Source Type of…

A:

Q: Take a 19 in. and 0 = 45°. (Figure 1) Figure 8 in. 8 in.-- 2 in. 2 in. 2 in. 1 of 1 Part A Determine…

A:

Q: The focal length of the object glass of a tacheometer is 320 mm, the distance between the vertical…

A:

Q: A soil is described as a “Silty clay, trace to some sand, trace fine gravel and cobbles”. Describe…

A: According to the description, the soil is mostly silty clay with trace quantities of sand, fine…

Q: For the beam below, take P= 6kN, a=1.5m. Use the Moment-Area Method to solve this problem. A EI=…

A:

Q: 1. Determine the force in members DG and FI of the truss shown. Draw a FBD and use the top section…

A: Determine  1. Force in member DG and FI by taking section-aa (top section).  2. Force in member GJ…

Q: A 97-kN axial load P is applied to the W150 x 8 rolled steel column BC that is free at its top C and…

A: P = 97 kN e = 6 mm  σa = 80 MPa E = 200 GPa or 200,000 MPa

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.