Measurement of a line was taken ten times with a steel tape and found to be as under 100.54 m, 100.56 m, 100.38 m, 100.36 m, 100.39 m, 100.46 m, 100.48 m, 100.32 m, 100.47 m, 100.52 m Assuming that the measurements have been corrected for all systematic errors, then the standard deviation of the mean is cm.

Measurement of a line was taken ten times with a steel tape and found to be as under 100.54 m, 100.56 m, 100.38 m, 100.36 m, 100.39 m, 100.46 m, 100.48 m, 100.32 m, 100.47 m, 100.52 m Assuming that the measurements have been corrected for all systematic errors, then the standard deviation of the mean is cm.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter19: Probability And Statistics In Engineering

Section: Chapter Questions

Problem 4P

See similar textbooks

Similar questions

A civil engineer measures the distance of points A and B and the following values were recorded in a series of measurements. Trials (T)1 with No. of Measurements (NM)= 200.58, T 2 with NM= 200.40; T 3 with NM = 200.38 and T 4 with NM = 200.46. Determine the average value (mean), probable error of mean, and precision of the measurements..
Measurement of a line was taken ten times with a steel tape and found to be as under 100.54 m, 100.56 m, 100.38 m, 100.36 m, 100.39 m, 100.46 m, 100.48 m, 100.32 m, 100.47 m, 100.52 m Assuming that the measurements have been corrected for all systematic errors, then the standard deviation of the mean is cm.
A surveying team used a 100m tape which is of standard length at 32°C in measuring a certain distance and found out that the length of tape have different tension were applied as shown. Let K = 0.0000116 m/°C. Length of tape (m) Tension Applied (kg) 99.986 10 99.992 14 100.003 20 a. What tension must be applied to the tape at a temperature of 32°C so that it would be of standard length? b. What tension must be applied to the tape at a temperature of 40.6°C so that it would be of standard length?
A quantity was measured ten times with the following results: 34.630 m, 34.626 m, 34.634 m,34.628 m, 34.629 m, 34.626 m, 34.627 m, 34.633 m, 34.625 m, and 34.624 meters. Determine the most probable value ,the probable error of the single measurement , the probable error of the mean and the relative precision.
Determine the probable error, standard deviation and standard error.
A bar of circular cross-section varies uniformly from a cross section 2D to D. If extension of the bar is calculated treating it as a bar of average diameter, then the percentage error will be (a) 10 (b) 25 (c) 33.33 (d) 50
A sample of 100 adult women was taken, and each was asked how many children she had. The results were as follows: Children 0 1 2 3 4 5 Number of Women 25 20 28 15 8 4 What is the sample mean and standard deviation in that order? Select one: a. 1.74 and1.41 b. 1.73 and1.40 c. 1.73 and1.41 d. 1.41 and1.73 e. 1.40 and 1.73
Compute for the mean deviation Mass Measured value 1 8.21 cm 2 8.24 cm 3 8.22 cm 4 8.23 cm 5 8.24 cm 6 8.22 cm 7 8.23 cm
find the following: a. Get the distances in 3 trials using the measuring tapeb. Compute the most probable value (mpv)
From the measured values shown, determine if the measurements are within the required precision. Show all computations. Allowable precision is 1/5000. Trials Distance (m) 1 220.87 2 220.90 3 220.93 4 220.89 5 220.81
You are tasked to measure a 2.1 m door with using only a ruler. On your first try you recorded a measurement of 217 cm. You repeat the measurement and obtain a value of 217 cm. What is the value of thie true percent relative error considering your most recent measurement? Note: Do not round off intermediate values and submit your answer in 2 decimaelates onl ry on vey
PLEASE ANSWER WITH COMPLETE SOLUTION. THANK YOU. A given distance was measured in four trials and came up with this values: 52.15m, 51.8m, 51.5m & 52.20m. Solve the residual of the first trial of measurement.