Q.1A/ Answer both MCQ sub-questions: 1. In the forced vibration, the motion of the spring( which is usually represented by a differential equation) is affected by: • Restoring force • Damping force • External force • All of the above d2x + 64x = 0 2. The motion of spring represented by the equation: Can be described as: dt2 • Overdamped • Critically damped • Underdamped • None of the above ural

Q.1A/ Answer both MCQ sub-questions: 1. In the forced vibration, the motion of the spring( which is usually represented by a differential equation) is affected by: • Restoring force • Damping force • External force • All of the above d2x + 64x = 0 2. The motion of spring represented by the equation: Can be described as: dt2 • Overdamped • Critically damped • Underdamped • None of the above ural

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An element is found in a stress condition as shown in figure Calculate (i) Principal stress and its orientation (ii) Maximum shear stress, its orientation and corresponding normal stress (iii) Normal strains in each direction 30Mpa 15Mра 20Mра
The beam shown in the figure below (Figure 1) is made of steel that has an allowable stress of σallow 14 ksi. Part A Figure く 1 of 1 Determine the largest internal moment the beam can resist if the moment is applied about the z axis. Express your answer to three significant figures. ΕΠΙ ΑΣΦ vec (Mallow) z = Submit Request Answer Part B ? kip.ft Determine the largest internal moment the beam can resist if the moment is applied about the y axis. Express your answer to three significant figures. (Mallow) y = ΕΠΙ ΑΣΦ vec Submit Request Answer 0.25 in 0.25 in. _ E 3 in. 3 in. To.25 in. < Return to Assignment 3 in. 3 in. Provide Feedback ? kip.ft
• What is the member force in CD? Indicate the negative (-) sign in your answer if the member is in compression. 12k 18 k 12 t D 36° 25 k 20 ft 16 ft
A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂ bonded to an 80-mm-long hollow rubber cylinder with a modulus of rigidity G = 10.93 MPa. Determine the required value of the ratio R2/R1 if a force P = 13 kN is to cause a 2-mm deformation of rod A. B R₁ R₂ .. 80 mm The required value of the ratio R2/R₁ is 1.422
The state of stress in a deformable body is shown in the figure. Consider transformation of the stress from the x-y coordinate system to the X-Y coordinate system. The angle 0, locating the X-axis is assumed to be positive when measured from the x-axis in counter-clockwise direction y = 120 MPa 40 MPa Oxy 50 MPa %3D 30% Oyy = 35.6 MPa The absolute magnitude of the shear stress component o,xy (in MPa, round off to one decimal nlace) in x-y coordinate system is
Take oz = 84 MPa and Tzy = 35 MPa (Figure 1) Part A Determine the equivalent state of stress on an element at the same point that represents the principal stresses at the point. Express your answers in ascending order separated by a comma using three significant figures. VO AEO t vec ? igure 01, 02 = MPа Submit Request Answer Txy Part B Also, find the corresponding orientation of the element with respect to the element shown. Express your answers using three significant figures separated by a comma. Hνα ΑΣφ vec (8,)1. (8,)2 =
Which of the following best describes distortion energy? A.Work done on an element by a force which causes deformation B.Energy stored in a material when it deforms C.Energy stored in a material needed to change its shape D.Energy stored in a material that causes a volume change For a ductile material experiencing principal stresses equal to 10 MPa (T) and 20 MPa (C), which of the following gives the closest value of the von Mises stress? A.17.3 MPa B.700 MPa C.26.5 MPa D.300 MPa If a ductile material (oY=36MPa) experiences principal stresses of 25 MPa (T) and 12 MPa (C), what would be the MINIMUM shear stress it can experience to fail under the Maximum Shear Stress theory? A.18.5 MPa B.6.5 MPa C.18.0 MPa D.37.0 MPa
1-A thin aluminum plate profile shown in the accompanying figure is subjected to an axial load. deflection and the average normal stresses along the plate using the model shown in the figure. The plate has a thickness of 0.5 cm and a modulus of Approximate the 2 cm 2 cm elasticity E=70 GPa 2 cm 2 сm 3000 N б ст 6 cm 10 cm 2 cm 2 cm
A high-strength bolt that passes through a steel plate is subjected to a tension force of P as shown in the figure. The hole in the metal plate has a diameter of D=17 mm which is slightly larger than the diameter of the bolt (d, = 12 mm) to allow for easy installation process. The plate has a thickness of t= 9 mm. The bolt head has a thickness of a = 9 mm and an outer diameter of dn = 24 mm. %3D Determine: A) the maximum value of P before the shear stress in the rod head exceeds Thot = 105 MPa. B) the maximum value of P before the punching shear stress in the support plate exceeds Tplate = 75 MPa. C) the maximum value of P before the bearing stress between the rod head and the support plate exceeds aplate = 110 %3D MPa. D) the maximum value of Pmax that can be supported by the structure.
The figure shows a rigid lever arm CBA that is pinned at A and connected to a wire at B. An applied force P causes the lever arm to rotate 0.05 degrees counterclockwise. What is the strain in the wire? P 300 mm C В A -400 mm-
The beam shown in Fig QB1 is made from aluminium tube of rectangular cross-section having a vertical height of 50mm, a horizontal width of 30mm and a wall thickness of 3mm. The dimensions given in the figure are in millimetres. The yield stress in tension is 200MPa; Young's modulus is 71GPa. Determine: an expression for the bending moment at every point in the beam and draw the bending moment diagram a) b) c) d) the maximum bending moment the maximum longitudinal stress the maximum vertical deflection 200 3kN 200 1kN 100
All of the following statements are correct except:a. Materials with higher modulus of elasticity, E are relatively weaker than those with lower E.b. Stress is proportional to strain within the elastic range.c. High carbon steel is stronger than concrete.d. In normal loading, the slope of the stress-strain curve is a material property called modulus of elasticity.The deflection of a beam is: A. Directly proportional to the modulus of elasticity and Moment of inertia B. Inversely proportional to the modulus of elasticity and moment of inertia C. Directly proportional to the load imposed and inversely to the length squared D. Inversely proportional to the weight and length