Q2) For a single phase (ac to ac) voltage controller, if the input supply voltage is (250Sin314t) with frequency (50 Hz) and the load is (R=5 2). Draw the controller circuit, and then do the followings: - a. Determine the rms value of the output voltage at firing angle (a-60). b. Determine the value of (a) in order to obtain output voltage of (70.7 V).

Q2) For a single phase (ac to ac) voltage controller, if the input supply voltage is (250Sin314t) with frequency (50 Hz) and the load is (R=5 2). Draw the controller circuit, and then do the followings: - a. Determine the rms value of the output voltage at firing angle (a-60). b. Determine the value of (a) in order to obtain output voltage of (70.7 V).

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

Design a single phase AC voltage controller which has supply voltage of 120, Vrms and 60 Hz. The output power the the circuit is 500 W. Determine the total harmonics distortion for the current (THDI). Your THDI must be lower than 10%.
A single phase half-wave AC voltage controller provides output RMS voltage of 50V when the triggering angle (a) is 90°. For the same a, what is the output RMS voltage if the AC voltage controller changed to full-wave type.
b. Describe how the zener stabiliser circuit reacts when: i. there is a fluctuation of the source (input) voltage. ii. there is a fluctuation of the output resistance (load).
QUESTION 3 a) In order to drive a DC motor, a square wave signal as shown in Figure Q3(a) is required. Due to cost factor, a 555 timer chip will be used for this purpose. i. Develop the timer circuit and calculate resistors R1 and R2, and the capacitor Cext in order to produce the signal. Draw and label the circuit. ii. Describe the effect of changes in (a) duty cycle and (b) frequency of the signal on the motion of the DC motor . 1 1.25 2.25 2.5 3.5 3.75 4.75 5 ms ms ms ms ms ms ms ms ms Figure Q3(a)
A 3-phase half wave controlled AC to DC converter is supplied from a 250V, supply. Assume the thyristor voltage drop to be 1.6V and the load current to be continuous. Evaluate the mean output voltage when firing angle is varied at 45(degree) , 60(degree) and 90(degree)
Electrical Engineering What is the difference between an SCR and a TRIAC in AC? What is the difference between the DC and AC operations of these thyristors?
What is the relationship of the gate pulses to the two thyristors in a full-wave ac phase control circuit? Explain why a diode is connected across the output terminals of a buck chopper.
Given the model for position control system, find the value for K1 and K2 so that the peak time is equal to 0.5s and the %OS is equal to 3%.
. Can you get a DC signal from the Digital Multi-Meter? If not, why?
By comparing the performance of DC -DC chopper with controlled rectifier circuit which one of the following statement is wrong ? O a. Efficiency is better in chopper circuit b. small filters are required in chopper circuit O c. Regenerative braking process is very slow in chopper circuit O d. Switching frequency is responsible for output ripples in chopper circuit Clear my choice
A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf constant of 0.20 V/rpm. The armature current is 6 A without any ripple. The armature resistance is 2 ohm. The converter is working from a 230 V, single phase ac source with a firing angle of 30°. Under this operating condition determine the speed of the motor.
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 240 V (RMS), 50 Hz. The delay angles of both thyristors are set to 45 degrees. The maximum RMS and average current ratings of the thyristor are equal to: Select one: O a. 33.94A and 21.6A O b. None of these O c. 24A and 10.8A O d. 48A and 26.09A Clear my choice