QUESTION 5) Two elastic bodies made of different materials are placed in a rigid cavity and their surfaces are in full contact. In the vertical direction, a uniform pressure force acts on body 1 with 120MPA and on body 2 with 40MPA. Calculate all the stresses in objects 1 and 2 and the length changes in the z-axis direction.

QUESTION 5) Two elastic bodies made of different materials are placed in a rigid cavity and their surfaces are in full contact. In the vertical direction, a uniform pressure force acts on body 1 with 120MPA and on body 2 with 40MPA. Calculate all the stresses in objects 1 and 2 and the length changes in the z-axis direction.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2. Determine the density of the rectangular component (i.e. a) in kg/m and the location of the equivalent point load measured from point A so that it causes an upward 50 N force and a 300 Nm couple moment reactions at A. A a kg/m 0.5 m
1) a Compressor with a diameter of 0,65 metres and a thickness (t)= 4mm Sigmax= 42 MPA and Sigmay=84MPA Calculate: The pressure P and Maximum In-Plane Shear Stress Tmaxvlak in MPA 2) an element has undergoing a rotation of Theta= 30 degrees Sigmax= 75 MPA and sigma y= 55 MPA. Calculate X', Y' and Txy" in MPA 3) A uniform Beam with a lenght of 2 metres to a-a and forces N=12kn and V=4kn. Calculate the main stresses sigma1 and sigma 2 [in MPA] 4) an element with the given stresses: Sigmax=75 MPA and Sigmay= 55 MPA Calculate the Absolute maximum shear stress in MPA )Tabsmax)
Both wires have a cross sectional area of 17 mm? and are constructed of the same material with a modulus of elasticity of 200,000 MPa. 1. Determine the wires' tensile stress at C. 2. Determine the wires' tensile stress at D. 3. Calculate the maximum displacement possible. 900 mm 450 mm C D 500 mm 1250 mm P=1500 N 1650 mm
Both wires have a cross sectional area of 17 mm2 and are constructed of the same material with a modulus of elasticity of 200,000 MPa. 1. Determine the wires' tensile stress at C. 2. Determine the wires' tensile stress at D. 3. Calculate the maximum displacement possible.
Derive the equation of the resonance frequency of the uniform cantilever beam shown below by using method of conservation of energy. [Solution tips: Umax, maximum strain energy is equal to max. kinetic energy of vibrating body.] j'm dx ( M(x)² T. U = max El xp- 1/2
The figure shown is a cross-section of the beam on the fixed support of a propped beam that has a moment of 72 kN-m. Determine the following: a. The location of the centroid from the extreme tension fiber. The moment of Inertia of the cross-section. The bending stress at the extreme compression fiber. d. Show the force and moment check of the beam. b. c. 70 mm 50 mm- 100 mm: 50.0000 130 mm- 100.0000 -350 mm- 100 mm-
Determine shear stress at support on cantilever beam as shown in figure. b = 300mm. 500mm mm 120kN/m -2.7m- 200mm
A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: w (2) = - + F 48 %3D The value of E is 200,000 Nmm² and the values of ly is 20 x 10° mm“ The maximum value of z for the beam cross section is +20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm?
6–119. Determine the maximum allowable intensity w of the uniform distributed load that can be applied to the beam. Assume w passes through the centroid of the beam's cross-sectional area, and the beam is simply supported at A and B. The allowable bending stress is o allow = 165 MPa. %3D A 15° 6 m w(6 m) 15° 15 mm 100 mm 100 mm 10 mm 15 mm 15° 100 mm Probs. 6–118/119
Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three forces. Two forces are known in magnitude and direction and shown in the Figure (150 N and 60 N). The third force is passing through the center of the semi-circle (point C). The resultant of all these forces is a single couple (750 N.m) counterclockwise. a) Determine the magnitude and direction of the third force. b) Determine the magnitude of moment (M). c) Replace the couple (M) by two vertical equal forces acting at D and E. d) Replace the force (150 N) by and single force at D and a couple. Radius 5 m 150 N 60 N
Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of 4=200 mm'. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. FEA 3m rigid B A 2m 1.5m
A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: F w (x) = E, ( - +4) %3D Ely 8. The value of E is 200,000 Nmm 2 and the values of ly is 20 x 106 mm4 The maximum value of z for the beam cross section is 20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm? Express your answer in Nmm2, as a number to 2 dp, without the units.