Situation 3: The magnitudes of the three forces acting on the plate are T₁ = 100 kN, T2= 80 kN, and T3 = 50 kN. 1. Determine the x-component of the resultant force. 2. Determine the magnitude of R. 3. Determine the coordinates of the point where R intersects the plate. 1.0 m T₁ 2 m 6 m 3 m T₂ 2m T3 2 m

Situation 3: The magnitudes of the three forces acting on the plate are T₁ = 100 kN, T2= 80 kN, and T3 = 50 kN. 1. Determine the x-component of the resultant force. 2. Determine the magnitude of R. 3. Determine the coordinates of the point where R intersects the plate. 1.0 m T₁ 2 m 6 m 3 m T₂ 2m T3 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

%3D QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the crss section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm 10 mm A-40 mm--r: 30 mm 30 mm 10 mm 10 mm
2. The lengths LAB = LBC = 200 mm and LCD = 240 mm. The diameter of parts AB and CD of the bar is 25 mm and the diameter of part BC is 50 mm. The shear modulus of the material is G = 80 GPa. What value of the %3D torque T would cause the angle of twist of the right end of the bar relative to the wall to be zero? 4 kN-m A 8 kN-m LAB B T LBC.
allowa quired wall thickness 2:11 .l 0.31 KB/S 64 Edit 16 A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E = 200 GPa. 36 mma 2 m OWhat is the displacement of the loaded end B of the bar? ® Determine the tensile stress induced in rod CD by the 80 kN load D If the allowable stress in rod CD is 124 MPa, what weight W can be safely 1.8 m 12m applied? w80 AN 1. A holl ow cir cular steel colum n is s ubjected toa compression load of 380 kN . The column has a length of 2.4 mn.and an outside dia meter of 187.5 mm. E - 200,000 MPa Determine the min. roquired wall thicknesss base on an allo wable com pressi ve stress of 48 MPa. Determine the min. required wall thickness based on 30 MPa. Determine the min. required wall thickness based on the allowable shortening of the colum n to b e 0.5 0 mm- allowable shear stress of C3D P-38 O kN 2.4 m 2. An 8 mm diameter steel rod, 20 m. long…
A two pinned end bars AB (Copper), A = 850 mm2, E = 120 GPa and BC (Aluminum), A = 1000mm2, E = 70 GPa is %3D subjected to a horizontal force of 100 kN applied at pin B as shown in the figure, determine the horizontal displacement of pin B. C B 100 kN 2.00m 45° 1.50m
The bent steel bar shown in Fig. P-906 is 200 mm square. = 4.2 MPa = 29.2 MPa; og 906. Determine the normal stresses at A and B. Ans. .211 A 250 mm- جاش A 200 mm 450 mm Figure P-906. 100 mm 500 kN 3
The horizontal member shown in the figure is loaded by 57 kN at E. It is supported by steel connector AB (E = 200 GPa, A= 615 mm² ) and aluminum connector CD (E = 70 GPa, A = 525 mm² ). Determine the deformation incurred by connectors AB and CD. Also, calculate the vertical displacement of E. 57 kN 0.5 m 0.3 m E B 0.25 m 0.5 m
To lower ends of the three bars in the figure two are the same level before the rigid homogeneous W=176kN block is attached. Each still bar has a length of 1.00 m, an area 500mm² and E=200 GPa. For the bronze bar the length is 1.6m, the area is 900mm² and E= 83 GPa. What is the stress developed in the bronze bar? What is the stress developed into steel bar? What is the elongation of each bar?
QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the cross section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm y 10 mm At-40 mm-- 30 гу 30 mm 10 mm 10 mm
2)For the supporting frame shown below: a) Determine the internal forces acting at section a-a. b) Determine the stress components that act at points A and B. IN = 2.6525x10-7 mª -300 mm 150 mm 2.5 kN a 12 mm 6 mm 6 mm 6 mm 36 mm'36 mm Section a – a
the largest axial P force that the given riveted joint can safely carry.calculate. Rivet diameter 28mm and plate width 340mm. Shear stress of the rivet1400 kg/cm2, crush safety stress of rivet 2800 kg/cm2and the platetensile safety tension 1400 kg/cm2will be taken. t1=21mm t2=38mm
a) A brass bar, having cross-section area of 900mm2, is subjected to axial forces as shown in figure 4.1 in which AB =0.6m, BC = 0.8m and CD = 1.0m. 40 kN 70 KN 20 kN 10 KN Figure 4.1 Find the total elongation of the bar. Take E = 1 x 10$ N/mm² %3D
Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque) and a tensile force, the axial tensile stress is 30 MN m-2 and the shear stress 50 MNm (Figure). Estimate the principal stresses and draw the inclined element with the principal stresses r= 6 mm d = 30 mm Y-face 50 X-face D= 40 mm. 30MN m2 30 50 MN m-