The drag coefficient for the car is Cp = 0.26, and the projected area into the 20°C airstream is 2.5 m². At this temperature Pa = 1.202 kg/m³ (Figure 1) gure < 1 of 1 > Part A Determine the power the engine must supply to maintain a constant speed of V = 160 km Express your answer to three significant figures and include the appropriate units. μА P= Value Submit Request Answer Units ?

The drag coefficient for the car is Cp = 0.26, and the projected area into the 20°C airstream is 2.5 m². At this temperature Pa = 1.202 kg/m³ (Figure 1) gure < 1 of 1 > Part A Determine the power the engine must supply to maintain a constant speed of V = 160 km Express your answer to three significant figures and include the appropriate units. μА P= Value Submit Request Answer Units ?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter18: Mathematics In Engineering

Section: Chapter Questions

Problem 6P

See similar textbooks

Similar questions

A piston 11.96 cm diameter and 14 cm long works in a cylinder 12 cm diameter. A lubricating oil which fills the space between them has Viscosity 0.65 poise. Calculate the speed at which the piston will move through the cylinder when an axial load of 0.86 kg is applied. Neglect the inertia of the piston. 1 14 cm VF- 0.86 Kgt
Estimate the power needed to overcome the aerodynamic drag of a person who runs at a rate of 100 yds (300 ft) in 10 seconds in still air. Express your answer in terms of horsepower. Assume CDA = 9 ft2 for the runner. NOTE: ρAIR = 2.38x10-3 slugs/ft3, 1 horse power = 550 lb∙ft/sec.
Estimate the power needed to overcome the aerodynamic drag of a person who runs at a rate of 100 yds (300 ft) in 10 seconds into a 29.3 ft/s tail-wind. Express your answer in terms of horsepower. Assume CDA = 9 ft2 for the runner. NOTE: ρAIR = 2.38x10-3 slugs/ft3, 1 horse power = 550 lb∙ft/sec.
The 1540-kg car has a velocity of 26 km/h up the 10-percent grade when the driver applies more power for 18 s to bring the car up to a speed of 67 km/h. Calculate the time average F of the total force tangent to the road exerted on the tires during the 18 s. Treat the car as a particle and neglect air resistance. | 10 100 Answer: F = i kN
Problem 14-27 The conveyor belt delivers crate each of mass M to the ramp at A such that the crate's velocity is vA, directed down along the ramp. If the coefficient of kinetic friction between each crate and the ramp is uk. determine the speed at which each crate slides off the ramp at B. Assume that no tipping occurs. Given: M = 12 kg V4 = 2.5 Hk - 0.3 g = 9.81 a =- 30 deg %3D a = 3 m 日|s
Oil flows thru a 50 mm diameter pipe having a head loss of 12 m. The length of the pipe is 120 m. long. If the oil has a Reynold's Number equal to 1600; a. compute the velocity of the oil flowing in the pipe. (unit of the answer is in m/s) b. what is the equivalent viscosity in stokes? (unit of the answer is in stokes)
The 250-lb concrete block A is released from rest in the position shown and pulls the 400 lb log up the 30° ramp. Plot the velocity of the block as it hits the ground at B as a function of the coefficient of kinetic friction ug between the log and the ramp. Let µk vary between 0 and 1. Why does the computer not plot results for the entire range specified? 400lb 250lb A 30 deg 20' Hints: -- Model the system as a dependent motion analysis and derive acceleration equations in terms of the unknown quantities -- Use MATLAB to solve this system of equations (you'll need one equation for each unknown!) Define uk as a range in MATLAB from 0 to 0 in 0.01 increments -- Plot the function of the velocity for the block as it hits the ground
) A 5-gal, cylindrical open container with a bottom area of 120 in²is filled with water and rests on the floor of an elevator. If cylindricalcontainer is accelerated upward at 3 ft/s², what resultant force doesthe container exert on the floor of the elevator during thisacceleration? The weight of the container is negligible. (Note: 1 gal= 231 in³)
Please solve the problem quickly including the free body diagram. I have 30mins
Assuming smooth contact surfaces, determine the reactions A, B, C and D on the cylinders as shown in the fig. Show your solutions in two ways. W 200 lb We400 lb to 5.6'
Given The tank shown has one curved surface restraining a body of static fluid, with the following dimensions: w- 5.00 m h1 = 2.5 m R1 = 0.85 m Required Determine the value of x-bar in metres, to the nearest 1000th. Water hl R1
Determine the mean effective pressure in kPa of a certain air -standard Diesel cycle which has a compression ratio of 16 and a cutoff ratio of 2. At the beginning of the compression process, the pressure and temperature of air is at 95,000 Pa and 300K, respectively. Roun-off your answer into two decimal places. hint: Linear Interpolation equation Y1 - Yo Yo (x1 – æ) + Y1 (x – ¤0) | y = Yo + (x – To) X1 - 20