Use the rectangular component method to solve the fol-lowing problems. Determine the magnitude R of the re-sultant of the forces and the angles 0, 6, and 6, betweenthe line of action of the resultant and the positive r-, y-, andz-coordinate axes for90 mm75 N180 Gm8O N100 N130 mm120 mm240 mm

Given Data: Magnitude of F1 is 80 N. Magnitude of F2 is 100 N. Magnitude of F3 is 75 N.

Answered: Use the rectangular component method to…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Replace the two forces shown by a force-couple system with the force acting at O. EASY B 360 mm 50 N 270 mm A 90 N
18. Replace the two forces shown by a force-couple system with the force acting at O. 360 mm 270 mm 50 N A 300 90 N
ENGINEERING MECHANICS STATICS Example 6\ The tether of the balloon exerts an 800-N force F on the hook at O. The vertical line AB intersects the x z plane at point A. The angle between the z axis and the line OA is 60 , and the angle between the line OA and F is 45. find the three components Fx, Fy, Fz F
pt321656&cmid%3D18824 The resultant of the three forces shown in the figure is 721 N and acts on the direction u-axis. F2=587 N F3=446 N a=41° F2 F, 450 F3 1a) Calculate the angle O (in degrees). Vant 1b) Calculate the F (in Newtons). anme
Q1: It is required that the resultant force acting on the evebolt in the Figure to be directed along the positive x axis and that F2 have a minimum magnitude. Determine this magnitude, the angle 0, and the corresponding resultant force. F, - 800 N 60 F2
Use the yiupn of the parabola to fill in the table. 10- (a) Does the parabola open upward or downward? O upward O downward .0. None (b) Find the equation of the axis of symmetry. -10 equation of axis of symmetry: || (c) Find the intercept(s). For both the x- and v-intercept(s), make sure to do the following. • If there is more than one, separate them with commas. • If there are none, select "None". x-intercept(s):|| y-intercept(s): (d) Find the coordinates of the vertex. vertex:
QI/ The rigid pole and cross-arm assembly is supported by the three cables shown. A turnbuckle at D is tightened until it induces a tension T in CD of 1.2 kN. Express T as a vector. Does it make any difference in the result which coordinate system is used? Ans. T = 0.321i + 0.641j – 0.962k kN, IC 1.5 m B 1.5 m G T= 1.2 kN 3 m 2 m 1.5m 3 m
use virtual work method to determine horizontal and vertical components of the deflection at joint B of the truss P D A E B -2 at L EA= = constant P A F |--
y-axis Q= 950N %3D P= B0ON 30° -> T= 100N 1axis 2= 300N 20 %3D NS-15 KN y componente oF all the forces abově. Express your answers in Newtons and indicate the Diredion. Fx = 300N> V Solve the x and %3D eg. Fy = 600 N
Problems: 1- Find the deflection curve for the beam shown, then find the reactions at the supports. (Neglect self weight) W В A L El constant WLx 4 wL'x + 48EI wL? wx* y = 24EI 3wL V В 5wL and M 8. Ans.: V A 16EI 8. B 8.
Deflection of Beams Use Castiglianos Theorem Given: X - 274 у-74 а-8 b - 4 C- 9 Problem #1 #1 Determine the vertical displacement of joint A. Each bar is made of steel and has a cross-sectional area of 600 mm². Take E = 200 GPa. B. 1.5 m- -1.5 m P = X a = A
2) The box beam is constructed from four boards that are fastened together using nails spaced along the beam every 2 inches. The beam is subjected to a maximum internal shear force of 475 lb. a) Locate the neutral axis and compute the moment of inertia for the cross-section in in*. [Ans. to check: 1 = 197.7 in¹] b) Calculate the first moment of area in in³ at each of the two connection interfaces (i.e. once for the top flange and once for the bottom board). Draw a clear sketch of the cross-section showing the neutral axis and the necessary dimensions to calculate the first moment of area. [Ans. to Check: Qtop = 31.2 in³] c) Compute the shear flow occurring between the wood and the nails at each of the two connection interfaces in lb/in. [Ans. to Check: qbottom = 49.0 lb/in] d) Design the section by choosing the required shear strength of the nails (in lb). Check both interfaces but choose only one assuming you would like to use the same nails for the entire beam. [Ans. to check: 75 lb…

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS