What should be the capacitance of a capacitor in series with a 250Ω resistor that will limit the current to 1.2 amp when the circuit is connected to a 600V 60cycle source. Calculate also the power factor in this condition.

What should be the capacitance of a capacitor in series with a 250Ω resistor that will limit the current to 1.2 amp when the circuit is connected to a 600V 60cycle source. Calculate also the power factor in this condition.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Related questions

Q: Convert into rectangular, polar and exponential form: Given: Z1= 2-j3 1. csch(Z1)

Q: The two-wattmeter method is used to measure the total power taken by a balanced three-phase load,…

A: This question belongs to circuit theory . It is based on the concept of power measurements by using…

Q: The value of the damping ratio (C) of a critically damped Second order system is 01 0-1 02. 04

Q: 1. A 3 phase, overhead transmission line has a total series impedance per phase of 200 ohms and a…

A: The Performance calculations of long transmission lines need is based on various parameters of which…

Q: 1. Compare and comment the two plots you have obtained in Figure 8.5. Which motor has higher torque…

A: The plots show the variation in speed (rpm) of 2 machines against developed electromagnetic torques…

Q: Find the Inverse Laplace of a) 1/s3-s b) (s-1)/s(s+1)2

Q: A feedback control system characteristic equation is shown below: 5³ +5² +5 +10=0 Fill in the Routh…

A: We need to find out Routh hurtwiz table for given characteristics equation

Q: 10-ohm resistor and 10 H inductor are connected in series across a source of 12 V. If the current is…

Q: + 4₁ = 10 μA 18 mV 0.6 k BJT transistor amplifier AUNL V=3.6V Activate Windr

A: BJT is a bipolar junction transistor transistor it have three terminal first one is base, second is…

Q: Use Laplace transform to obtain the output current i(t) in ampere for t = 1 second for the given…

Q: Solve the base voltage of a voltage-divider bias circuit with Vcc=9V, R1=560k ohms, R2=560k…

Q: The position of a point in cylindrical coordinates is specified by (4,2π/3,3). What is the location…

Q: Find Leq 77 pH نعقد 17 pH m m 4 nH -Lea] b 12 nH ele 72 pH m 1 nH ell 7 pH m 14 pH

Q: What is the equivalent transfer function of the following block diagram? R(S) 1 C(s)

Q: Refer to the given circuit below. Using Superposition Theorem, determine the percent contribution of…

Q: PROBLEM NUMBER TWO: The closed-loop transfer function of a negative unity feedback system is given…

A: Given: The closed loop transfer function is Ts=s-2s2-K+2s+2K+5

Q: Show your solutions clearly and systematically. The D latch of Figure 1 is constructed with four…

A: D Latch is an electronic device. D Latch are store one bit of information. its always a single…

Q: Discuss the link between Electromagnetic waves and Light according to JC Maxwell.

A: JC Maxwell has a major contribution in finding the relationship between light and Electromagnetic…

Q: With Rf=l00K and R1 and R2 =100K in the summing Amplifier what is the value of output voltage for…

Q: SUBJECT: Industrial Electronics Display the waveforms of the four distinct kinds of time-delay…

A: Time Delay relay: When the coil is either energized or de-energized, certain relays have a "shock…

Q: A 1500kVA, 3phase, 60Hz, 6.9kV, wye-connected alternator has a field resistance of 0.45Ω and an…

Q: For a negative unity feedback system with the given forward transfer function, G(s) = 500 (s + 2) (s…

Q: The min and max value of RL to keep VRL = 5V is IR ΙΚΩ www R Iz V₁ = 50 V V/₂=5 V IZM=32 mA }{₁ O…

A: In this question we need to find a minimum and maximum value of RL to keep voltage across load…

Q: h(n) 0 n

A: poles and zero determine the function is stable or unstable. The frequency of value of denominator…

Q: The closed-loop transfer function of a negative unity feedback system is given by

A: NOTE- “Since you have posted a question with multiple sub-parts, we will solve first three subparts…

Q: 24. For the system of Figure P10.5, do the following: [Section: 10.10] a. Plot the Bode magnitude…

Q: A 10-ohm resistor and 10 H inductor are connected in series across a source of 12 V. If the current…

Q: Solve the collector-emitter voltage (VCE) of Figure 612. VCC T8V Beta = 110 R2 3.9kQ Figure 612…

A: We need to find out collector to emitter voltage for given circuit

Q: For the common emitter, which equation is correct OB=a/(1-a) OB=(1-a)/a OB = 1/(1-a) O B=a/ (1 + a)

Q: Solve the base current (IB) of Figure 612. VCC 8V R1 3.3ΚΩ 26.10 UA 28.8 uA 32.12 UA Beta = 110 R2…

Q: The initial and final values of f(t)=15-10t-10e e-20r are respectively (a) 5 and ∞ (b) 5 and -co (c)…

A: Given function, ft=15-10t-10e-20t

Q: The characteristic equation of a given system is s4 + s3 + 2s2 + 12s + 10 = 0. The stability…

A: Consider the given characteristic equation is: s4 + s3 + 2s2 + 12s + 10 = 0.

Q: For a series R-L circuit i(t)=√√2 sin (cot-45°) If @L=1 Q, the value of R is (a) 1 Ω (b) 3 Ω (c) 13…

A: Phase angle in series RL circuit calculated tanϕ= WL/R From the given current expression, we can…

Q: Solve the collector current of a fixed-bias circuit with Vcc= 10V, RB=310kohms, RC=2.1kohms, and…

A: We need to find out collector current for given fixed bias circuit

Q: Given an Ideal OP-AMP with the following parameters: R1 = 680 2, R2 = 100 92, R3 = 1802, Rf = 2.7…

Q: The power consumed by a coil is 300 W when connected to a 30 V dc source and 108 W when connected to…

A: We need to find out reactance of inductor for given power

Q: In an inverting op-amp, has the following. Rf=20K, R1=5K and Vin=3 volts. What is the gain of this…

Q: The LED usually turns ON in the .......... Not Forward and not reverse Reverse Biased O Forward…

Q: If u(t) is the input to the system H(s) = 1/(s+100), the output of the system would be: O A. None of…

Q: A wire is 21.0 m long at 3.50°C and is 1.66 cm longer at 36.5°C. Find the wire's coefficient of…

A: Given, A wire has L0=21.0 m at T0=3.50°CL=1.66 cm at T=36.5° C

Q: 8.18. Suppose that each cell in a 1-Gbit memory chip must be refreshed every 10 ms. What is the…

A: Calculating the power dissipated in refreshing a 1 Gb memory chip.It is known that the power…

Q: Q1. A 10 cm length of a K-band (a = 1.06 cm and b = 0.43 cm) copper (o= 5.8x107) waveguide is filled…

A: A 10 cm length of a K-band (a=1.06 cm and b=0.43 cm copper σ=5.8×107 waveguide is filled with a…

Q: D7.5. Calculate the value of the vector current density: (a) in rectangular coordinates at P₁(2, 3,…

A: We need to find out current density for given magnetic field

Q: Given circuit represent the logic for which gate? A B Select one: a. None b. NOR c. OR d. NAND e.…

A: Given logic circuit:

Q: Gp(s) R(s) S c(s) (s + 2)(s² - 25) Figure Q2a The transfer function of an inverted pendulum plant is…

A: Transfer function- Transfer function basically is the mathematical representation of the systems…

Q: Stability is based on a natural response that decays to zero as time approaches infinity. True…

A: from the question Stability is based on a natural response that decays to zero as time approaches…

Q: Consider a voltage source v(t) = 220 cos (100nt - 30°) Define a. The amplitude of v(t) b. The…

Q: 3.6 Solve for V₁ in the circuit of Fig. 3.55 using nodal analysis. 10 92 www 492 www www 10 V 20 V…

A: This question belongs to circuit theory . It is based on the concept of nodal analysis in the…

Q: rive the Vo response for non inverting summing amplifer circuit below using term Rf, Rg, R1 and :…

Q: If the L[ eat cos2t] = (s-a)/( s² - bs +31), determine the value of a.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
Three capacitors having values of 2.2 F, 280 F, and 470 pF are connected in parallel. What is the total capacitance?
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
In the circuit shown in the following figure(Figure 1) the capacitor has capacitance 19μF and is initially uncharged. The resistor Ro has resistance 11 2. An emf of 84.0 V is added in series with the capacitor and the resistor. The emf is placed between the capacitor and the switch, with the positive terminal of the emf adjacent to the capacitor. The small circuit is not connected in any way to the large one. The wire of the small circuit has a resistance of 1.1 /m and contains 25 loops. The large circuit is a rectangle 2.0 m by 4.0 m, while the small one has dimensions a = 13.0 cm and b = 18.0 cm. The distance c is 5.0 cm. (The figure is not drawn to scale.) Both circuits are held stationary. Assume that only the wire nearest the small circuit produces an appreciable magnetic field through it. Part A The switch is closed at t = 0. When the current in the large circuit is 4.70 A, what is the magnitude of the induced current in the small circuit? Express your answer with the appropriate…
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
What is the equivalent resistance ?? and what is the total inductance ??
An inductor of 230 milli Henry, a capacitor of 15 micro farad and a 200 ohm resistor are in series across a 36 V and 60 Hz voltage source. Find the total current a. 150 mA b. 0.164 A c. 0.2 A d. 170 mA
Two identical coupled inductors are connected in series. The measured inductances for the two possible series connections are 380 microH and 240 microH. Their mutual inductance in microH is ?