Write the F1 as Cartesian vector. F1 = 100 lb 0 = 35 deg = 40 deg
Q: A gas, whose composition is not known, has 40 BTU of paddle-work input at a constant volume of 20…
A:
Q: A rigid, perfectly insulated system contains 0.53m3 of helium at 1000 kPa. The system receives 1000…
A: Since the container is rigid, the volume of the helium remains the same. Also, the adiabatic index…
Q: 1) Sketch, then calculate the components of the following vectors. $ 5) 79° 11.4m 300m @ 22° E of N…
A:
Q: A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of…
A:
Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…
A:
Q: A compound epicyclic gear is shown diagrammatically in the Figure 1. The gears A, D and E are free…
A:
Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…
A:
Q: Steam enters a turbine operating at steady state at 850°F and 450 lbf/in² and leaves as a saturated…
A:
Q: An insulated rigid tank is divided into two compartments by a partition. One compartment contains 8…
A:
Q: The Newton's law of viscosity can be expressed in mathematical form as T=u (dv/dv)
A: This question is based on the concept of Newton's law of viscosity.
Q: 4. If am ion chamber reads 120 R when it was actually exposed to 132 R, and the temperature is 22°C,…
A: Given Data: (4) Reading of ion chamber Rc=120 R But the actual working condition Rw=132 R…
Q: What is the rate of heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if…
A: Given:Area of celotex, A=3 ft x 8 ftThickness, t=1 inTemperature of one surface, T1=80°FTemperature…
Q: 6. An auditorium is to be maintained at a temperature of 26°C & 50% RH, Air is to be supplied at a…
A:
Q: A pump has a brake horsepower of 35 hp with an efficiency of 68%. Neglecting frictional losses,…
A:
Q: What happens in the powder mixture if granulation is over wetted and under wetted? How can this be…
A: To be explained :- Effect of wetting on powder mixture
Q: A new sports car has a drag corfficient of 0.30 and a frontal area of 21ft^2, and is traveling at…
A: Introduction In this problem, we will calculate the power required to overcome aerodynamic drag by…
Q: Give the Following: Page 1 - Explanation of table (formula of Speed of sound for metric system) Page…
A: The altitude data in meters is as shown below. height(ft) height(m) sea level sea level 1050…
Q: A new sports car has a drag corfficient of 0.30 and a frontal area of 18.5 ft<, and is traveling at…
A: Given data. drag coefficient = 0.30 Frontal area = 18.5 ft^2 Speed = 90 mi/h Density = 0.002378…
Q: Oil flows in a pipe 80 mm bore diameter with a mean velocity of 0.4 m/s. The density is 890 kg/m3…
A: Given: pipe bore diameter, D = 80 mm = 0.08 m mean velocity, V = 0.4 m/s density of oil, ρ = 890…
Q: 2) The ballistic pendulum is a simple device to measure projectile speed v by observing the maximum…
A: Given data :- Mass of projectile = 40 g Mass of box = 16 kg Maximum angle = 23° Brief introduction:-…
Q: As shown in the figure, air with a volumetric flow rate of 14.000 ft/min enters an air-handling unit…
A: Given DataV˙1=14000 ft3/minP1=1atmT1=80FT2=45Fd4=50ind2=26in
Q: Draw the V and M diagrams, find the deflection under the 75 klb load and the displacement of point…
A: The free body diagram of member BC is RBH and RBV are the horizontal and vertical resistance force…
Q: 3.15.) In air conditioning unit, 71,000 cfm at 80°F dry bulb 60% th and standard atmospheric…
A: Given Dataϕ1=60%ϕ2=90%Q=71000cfmTdb1=80FTdb2=57FHere standard pressure Patm=14.7 psia ***Note As per…
Q: Carbon dioxide gas is compressed at steady state from a pressure of 16 lb/in² and a temperature of…
A:
Q: Refrigerant 134a enters an insulated diffuser as a saturated vapor at 80°F with a velocity of 800…
A: Given Referigerent-R134aT1=80oFV1=800ft/s=800×0.3048=243.84 m/sA=1.4 in2=1.4×0.02542=9.03224×10-4…
Q: 9mm Ġ Diameter 5mm x 10 150mm (Aluminium 6060) An aluminium block with holes drilled through all…
A: Write the given data with suitable variables. L=300 mB=150 mm=0.15 mH=9 mm=0.009 md=5 mm=0.005…
Q: Make 2 free body diagrams
A: The free body diagram for the point B is as shown below. Here, FAB and FBC are the forces in the…
Q: For a hydroelectric plant, a hydraulic turbine-generator is installed at the site below the free…
A: Given Datah=20mWf=100kWWsh=80kWηturb-gen=0.7
Q: m L O a L/2 8.0 g k
A: Given,
Q: A bar made of A-36 steel has the dimensions shown below. If an axial force of P = 65 kN is applied…
A:
Q: An oil pump operating at steady state delivers oil at a rate of 11 lb/s through a 1-in-diameter exit…
A:
Q: Refrigerant 134a enters a well-insulated nozzle at 200 lbf/in.2, 140°F, with a velocity of 120 ft/s…
A:
Q: 1) Show that the Drag equation is homogenous in both SI units and basic units. 1 FD CD Apv²
A: following is the solution to the above problem-
Q: A fan is to accelerate quiescent air to a velocity to 20.00 m/s at a rate of 2.00 m3/s. If the…
A: Given data as per the question velocity = 20 m/s Flow rate = 2 m3/s The density of air = 1.15 kg/m3
Q: w[N/m] wohn(x) 8m Find the location of the application of the resultant force to genovare the…
A:
Q: 1. ) Question : A pump has a brake horsepower of 35 hp with an efficiency of 68%. Neglecting…
A: Given:Brake power of the pump, BP=35 hpEfficiency of the pump, η=68%Height of discharge, h=60 m
Q: If the specific gravity of the gasoline is 0.68, determine the pressure at the gasoline-water…
A:
Q: Part A The depth of water behind the Hoover Dan is houd 230 Cacu the water pressure c Express your…
A: Given:Depth of water behind the dam. h=230 m
Q: Required information Water flows through a two-dimensional narrowing wedge at 23.18 gal/min per…
A: Introduction The velocity potential function of space and time whose negative derivative with…
Q: 1. A 10-cm-diameter siphon tube is used to empty the reservoir and discharge it into the air (Figure…
A:
Q: Determine the units of pressure in the equation pv=RT v: specific volume, m3/kg R: constant in…
A:
Q: An insulated 8 m³ rigid tank contains air initially at 305K and 181 kPa. A 15 heater running off a…
A: Given, Volume V¯ = 8 m3 T1 = 305 K P1=181 kPa R=15 ? Voltage V=108.1 V P2=362 kPa
Q: For a hydroelectric plant, a hydraulic turbine-generator is installed at the site below the free…
A:
Q: 8. A nylon-core flat belt has an elastomer envelop; is 200 mm wide, and transmits 60 KW at a belt…
A: (A) Write the given data. w=200 mmP=60 kWv=25 m/sm=2 kg/mC=6 mD=300 mmd=900 mm
Q: A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000 rpm. The gears…
A:
Q: A punching press pierces 40 holes per minute in a plate using 10 kN-m of energy per hole during each…
A:
Q: Part A - Molar mass A gas mixture contains 3.6 kg of H2 with M_bar1 = 2.02 kg/kmol , 8.1 kg of N2…
A: Given data: m1=3.6 kgM1=2.02 kg/molm2=8.1 kgM2=28.01 kg/molm3=3.6 kgM3=39.95 kg/mol Need to…
Q: Determine the reactions at the supports A and B of the beam shown below.
A:
Q: Which definition of Reynolds number is correct (U - reference velocity, D - characteristic…
A: Given data :- U = reference velocity D = characteristics dimension n = kinematic viscosity. Drive…
Q: For the direct shear example shown below, if F = 47 kN, AAB = AcD = 3151 mm², the average shear…
A: Given:Force acting, F=47 kNArea of the surface, AAB=ACD=3151 mm2
Step by step
Solved in 3 steps with 3 images
- i need help solving for F ite the force F in Cartesian vector form and determine the direction cosines. Use point C as (1.5, -1, 3)ft. S: lb, 115°, 73°, 149° F-80 lb 311 6 ft(b) v = 8.9i+ 4.8j. d. The point A has coordinates (4,1), AB= 9 5 BC= . Find the coordinates of B and the column vector representing CA. 1a. What is the position vector that starts at -50j and ends at 50 j? b. What is the position vector that starts at (-50 i - 20 j +10 k) lb and ends at (50 i + 20 j -10 k) lb c. What is the resultant sum of the moments in Cartesian vector form? Round your entries to the nearest whole number.
- Write the position vector rB/A that points from point A to point B.Find the magnitude of the resultant vector in the following system of non collinear vectors. F1: Magnitude 50, Direction 120°F2: Magnitude 30, Direction 30°$ Magnitude R= Direction 8 = Three forces act on point : A = 60 N at 135°, B = and C in this diagram to the correct magnitudes and directions. When this has been done correctly the dotted vector will become solid. 50 N at -45° and, C= 75 N at 60° 2. Pick up vectors A, B and C by their tails, and move them into a tip to tail arrangement. When this has been correctly done the resultant R will appear. measured Estimate the magnitude and direction of the resultant Based on this diagram, estimate the magnitude R and direction of the resultant. from the force R using the tip-to-tail method. 1. Move the tips of forces A, B, Submit part Submit part
- Find the vector format for vector AB. Find the coordinate angles for AB. 5 ft B7 ft ✓ x Z 10 ft 30⁰ 70° A - yThe vector from the origin to point A is given as 6a, - 2a, – 4a., and the unit vector directed from the origin toward point B is (.-1). If points A and B are 10 units apart, find the coordinates of point B.Express F= 100N (shown in the figure below) as a Cartesian vector.
- Express a vector in Cartesian Vector Form for the following: Magnitude of Force: F= 864 Ib Line of action of force passes through points from A (12,6,-5) towards B (-5,2,-3). What is the x (f) component of the force vector rounded to one decimal place? Enter your answer as positive or negative.Eight points in the cartesian system are as follow: A(-9, 3), B(-5, 6), C(2, 2), D(5, 6), E(-2, -5), F(-8, 0), G(2, -3), H(9, -3) Draw and label the vectors on a graph. For each vector, determine the components of the related position vector. Determine the magnitude of each vector. Determine the direction of each vector with a horizontal line, and bearing angle....The position vector rAB = 150i – 85j + TAB2 k has magnitude equal to 188 m. a) Determine the z-component r48 2 (positive). b) If the coordinates of point A are (25, 50, -20)m, define the coordinates of point B. c) Find the angle in degrees of the vector with the y-axis. d) Express a unit vector parallel to rAB in terms of components.