choose the correct answer Y 8 - 200450 mmd' = 35 mmfy = 460 N/mm?All dimensions are in mmSingly reinforced simply supported beam.Calculate the shear force resisted by the stirrups Vus ?Select one:O a. 162 kNO b. 95.45 kNO c. 125.6 kNO d. 100.5 kN

Given data: fy=460 N/mm2d'=35 mm

Answered: Y 8 - 200 450 mm d' = 35 mm

Engineering

Civil Engineering

Y 8 - 200 450 mm d' = 35 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7. A steel bar of 25 mm diameter is acted upon by forces as shown in Fig-2. What is the elongation of the bar? Take E - 190 GPa. 60 kN4 A A ا 20KN B C 30 kN B C -2m-1m 3m 2* Figure-2 D D 50 KN
PRINTER VERSION 1 BACK Question 8 Draw the shear and moment diagrams for the beam loaded at its center by the couple C. Then answer the questions. The distance x is measured from point A to the right. C. 0.5 L- 0.5 L- Questions: At x = 0.37L, V = C/L, M = Jc. %3D At x = 0.81L, V = C/L, M = IC. www At x = 0.50L, V = C/L SAVE FOR LATER SUBMIT ANSWER Question Attempts: 0 of 2 used 11:31 PM 2/18/2021 W Paso F11 01
d%315KN/m (Including wt. or Beam (B1) Q3// Design for shear for beam (B1) shown in the Figure if f'c = 25 MPa, Fy diameter of bar = 16 mm, WL= 35 kN/m, Wd=15KN/m. 700 mm 420 MPa, %3D 210 mm 300 mm 650 mm
Q2 All members of the truss in Figure Q2 are to be fabricated from the same stock of thin-walled, round, steel tubing. Two external loads are exerted at the edge of lower part of member BF and CE with magnitudes of 10kN and 15KN, respectively. The loads are placed in a vertical position abiding gravitational direction. Analyse the truss structures based on the instruction listed. (i) Among all rods of the truss shown in the figure, there is a member that supports no loading known as a zero-force member. Figure out the member(s) with solid justification. (ii) The truss is supported with two surface forces as shown. Determine the magnitude and direction for each support reaction. (iii) Determine the axial stress in all rods of the truss by mentioning either the rod is experiencing compression or tension.
i li. In. e Google Translate العربية الإنجليزية - الإنجليزية A singly reinforced beam 250x500mm in a section is reinforced with four bars of 16mm diameter with an effective cover of 50mm. Effective span of simply supported the beam is óm. Assuming f'c=2OMPA and fy=415MPA. Determine the central concentrated force that can be carried by the beam. تحويل الصوت إلى نص كاميرا العربية يتم تعزيز العارضة المقواة بشکل فردي 250 x 0 50 م م في مقطع بأربعة قضبان بقطر 16 م م مع . فعال يبلغ 50 م م. المدى الفعال ل لشعاع المدعوم ب بساطة هو m. بافتراض fc = 20MPa و = fy 415MPA. حد د القوة المركزية المركزة التي يمكن أن تحملها الحزمة. elbi %3D %3D ytmu taeziz alearidat almuqwat bishakl fardi 250 * 500 mima fi .
PROB: COMPUTE THE FORCE IN EACH MEMBER OF THE TRUSS Stown In TISE FIGURE USING MOJ. 8kN 24m с 2.4 8kN 41 36m. 2.4m 8 kH D 2.4 M. PORTRAIT ORFentanon. TABULATE YOUR ANSWERS. NO TAB NO PTS.
Design the positive moment of the beam shown below, determine the number of 16mm diameter bars and the tension steel area, As. Assume the loads given are already factored. b=320mm d=480mm fc'=27MPA fy=300MPA As = || sq.mm. 50KN 3m | 20 KN/m
A.) CREATE A SHEAR DIAGRAM BY AREA MOMENT AND BY PARTS B.) CREATE A M/EI DIAGRAM BY AREA MOMENT AND BY PARTS ITEM 1.0 2 k/ft AF C В -15 ft- -6 ft EI = constant E = 29,000 ksi I = 3,500 in.4
Problem 23.4. A hook carries a load of 7.5 kN and the load line is at a distance of 20 mm from the inner edge of the section which is trapezoidal. The load line also passes through the centre of curvature of the hook. The dimensions of the central horizontal trapezoidal section are : inner width = 30 mm ; outer width = 15 mm ; depth = 30 mm. Calculate the maximum and minimum stresses. Also plot the variation of stress across the section. %3D Sol. Given : HE.1000 NT
05. Analyze completely the complex truss loaded as shown below using the method of Henneberg, 6 m 30 30 PROBLEM 5 TABLE OF ANSWERS: МЕМBER NUMBER FORCE (k) AF 1 EF DE CD BC 5 AB AD 7 CF 8 ВЕ 9. 2. 3. 4.
q kN/m 2 C A EI 2EI El В 3 m 6 m Baska yönergeler aimak için tiklayın Using cross method, determine the dictribution faotors for oross method (DF,, DF, DF, and DF and Internal bending moment at seotions 1, 2, 3 and 4 (M,. M, M, and Ma in the ftrame? q= 25 kNim (If you find a negative value ac your final ancwer, DON'T take abcolute, write down the exaot value with correot cignt! For end momente, define correot sign acoording to sign oonvention in DIAGRAM BII) (Use."dot" for deoimais and submit your answer with 2 digits) DF1 = DF2 = DFy = DF = M: = kNm kNm My = kNm M4 = kNim 3.
A 200mmx400mm rectangular beam has 5-20mm diameter rebar at the tension side and 2-20 diameter rebar at the compression side. Determine the design moment capacity of the beam in (kN-m). [Answer in 3 decimal places] Given: db(main bars)=20mm dbs(stirrups) = 10mm concrete cover = 35mm fy = 420 MPa fc' = 35 MPa 169.576 kN-m 163.161 kN-m 156.278 kN-m 153.018 kN-m