Pasco Synthesis

In this Chemistry Lab the main objective is to perform accurate chemical analysis for the quantity of elements and compounds in a sample. There will be a compound made then synthesized. The methods used were acid-base titrations, redox titrations, gravity filtration, and distillation. General conclusions included

4. To utilize the titration results to calculate the molarity of the hydrochloric acid and the

The purpose of this experiment is to determine an unknown concentration of acid (hydrochloric acid) with a standard solution of a base (sodium carbonate) using titration method.

The Distilled water pH average of HCl for zero drops was 6.67, and the pH for the final thirtieth drop

We only added a small amount of HCl to the water and sodium chloride. We did not continue to add more HCl after a significant drop in pH was recorded. We added a total of 2 mL of HCl to both H20 and NaCl before the pH changed. The 1 gram solution of sodium acetate and acetic acid changed after a 8 mL, and the other two never dropped before we reached our total of 10 mL HCl.

Chemistry 102 is the study of kinetics – equilibrium constant. When it comes to the study of acid-base, equilibrium constant plays an important role that tells how much of the H+ ion will be released into the solution. In this lab, the method of titrimetry was performed to determine the equivalent mass and dissociation constant of an unknown weak monoprotic acid. For a monoprotic acid, it is known that pH = pKa + log (Base/Acid). When a solution has the same amount of conjugate base and bronsted lowry acid, log (Base/Acid) = 0 and pH = pKa. By recording the pH value throughout the titration process and determining the pH at half- equivalence point, the value of Ka can be easily calculated. In this experiment, the standardized NaOH solution has a concentration of 0.09834 M. The satisfactory sample size of known B was 0.2117 g. The average equivalent mass of the unknown sample was found to be 85.01 g, pKa was found to be 4.69, which was also its pH at half-equivalence point and Ka was found to be 2.0439×〖10〗^(-5). The error was 1.255% for equivalent mass and 0.11% for Ka. In other word, the experiment was very precise and accurate; the identity of the unknown sample was determined to be trans-crotonic by the method of titrimetry.

The materials needed for this experiment included test tubes, a test tube holder, the unknown compound #202, 35mL beakers, gloves, safety goggles, ethanol (to clean equipment), stirrer (to mix solutions), the 15 possible compounds that are provided, pH strips, distilled water, wooden splints, spatula to get out unknown compound #202, waste bucket, Bunsen burner, graduated cylinder, 500mL beaker for the waste, plastic dishes to measure out compound and the scale.

This is the point of stoichiometric equivalence, meaning the number of mols of both substances are equal. The mols used in the known solution can be found by multiplying the molarity by the volume used in titration. The molarity of the unknown solution can be found by dividing the number of mols, which is equal to the number of mols titrated in the known solution, by the volume in liters of the unknown solution. Titrating in this lab works because the one H+ ion in the KHP and HCl consumes and neutralizes the one OH¬- ion found in the NaOH. Standardization involves titrating the same solution multiple times to obtain an average molarity of the solution from the many

ii. The second part of the titration series involves titration of NaOH with Hydrochloric acid (HCL). Again, three reps of titration and a blank titration have to be completed. A volumetric pipet is used to measure 10.00mL of HCL into three labeled conical flasks. Then the flasks are filled with deionized water until about the 50mL mark. A buret is

The purpose of this experiment was to determine the molar solubility, the solubility constant, and the effect of a common ion on the molar solubility of calcium hydroxide. To accomplish this the experiment was split into two parts; part A and Part B. in Part A of the experiment a standardized 0.05 M solution of HCl was titrated into a 25 mL solution of saturated Ca(OH)2 which contained 2 drops of orange methyl identifier. Once the titration began, the HCl was added until the methyl orange endpoint was reached, and as a result the volume of the HCl needed for the endpoint to be reached could be used in

During a titration the pH of the solution will be monitored using a pH meter from that we get a titration curve. The titration curve is then used to determine the equivalent molecular weight and Ka value of the unknown weak acid, from that we are

First, three titration curves and three second derivative curves were created to determine the average pH at the half-equivalence point from the acetic acid titrations. Titration curves were used as visuals to portray buffer capacity. The graphs and a table, Table 1, that showcased the values collected were created and included below. The flat region, the middle part, of Figures 1, 2 and 3, showed the zone at which the addition of a base or acid did not cause changes in pH. Once surpassed, the pH increased rapidly when a small amount of base, NaOH, was added to the buffer solution. Using the figures below and

The purpose of this lab was to use process titration to find concentration of an aqueous solution of Hcl(aq) , using KOH(aq) as the titrant.

An acid-base titration is the determination of the concentration of an acid or base by exactly neutralizing the acid/base with an acid or base of known concentration. This allows for quantitative analysis of the concentration of an unknown acid

For this experiment, a pH meter was used so this part of the experiment began with the calibration of the pH meter with specified buffers. The buret was then filled with the standard HCl solution and a set-up for titration was prepared. 200g of the carbonate-bicarbonate solid sample was weighed and dissolved in 100 mL of distilled water. The sample solution was then transferred into a 250-ml volumetric flask and was diluted to the 250-mL mark. The flask was inverted several times for uniform mixing. A 50-mL aliquot of the sample solution was measured and placed unto a beaker. 3 drops of the phenolphthalein indicator was added to the solution in the beaker. The electrode of the pH meter was then immersed in the beaker and the solution containing the carbonate-bicarbonate mixture was titrated with the standard HCl solution to the phenolphthalein endpoint. Readings of the pH were taken at an interval of 0.5 mL addition of the titrant. After the first endpoint is obtained, 3 drops of the methyl orange was added to the same solution and was titrated with the standard acid until the formation of an orange-colored solution. Readings of the pH were also taken at 0.5 mL addition of the titrant.