.. State the type of error that occurs in the following situations and suggest one (1) method to reduce the error:- A person using an ohmmeter reads the measured value as 4702, when the actual value is 472. A voltmeter has a specification as below:- (i) (ii) Items Specification 0– 250 V Range Аccuracy ± 1% full-scale deflection The voltmeter is to be used to measure voltage across resistor, R1. The expected value of the voltage across resistor, R1 is 125V; however measurement yields a value of 130V.

.. State the type of error that occurs in the following situations and suggest one (1) method to reduce the error:- A person using an ohmmeter reads the measured value as 4702, when the actual value is 472. A voltmeter has a specification as below:- (i) (ii) Items Specification 0– 250 V Range Аccuracy ± 1% full-scale deflection The voltmeter is to be used to measure voltage across resistor, R1. The expected value of the voltage across resistor, R1 is 125V; however measurement yields a value of 130V.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 14RQ: 14. A 6-V lead-acid battery has an A-hr rating of 180 A-hr. The battery is to be load-tested. What...

See similar textbooks

Similar questions

Explain the operation of an analog voltmeter.
Given this circuit: A voltmeter is placed across the resistor 47 ohm and its reading is -2.5V, Determine whether the diode is functioning properly or not.
Draw the block diagram of digital Multimeter and explain the measurement of D.C voltage
Question 5 Assume the zener diodes are all ideal in the circuit below and let V1=3.7 V, R1=935 2, R2=1,04702, and R3=855. Determine the output voltage Vo. Express your answer in Volts and round to the 1st digit to the right of the decimal. R1 V1 D1 5V R2 D2 3V {R3 D3 2V Vo
Write a short note on: a. Voltmeter b. Digital Multimeter
Summarize on how testing is carried out on isolators and circuit breakers of high voltage system. High voltage engineering
Q1.) a) PMMC meter has (10mA) half scale current deflection and (1500) internal resistance. Use this meter to design a dc multimeter of indirect ammeter and direct voltmeter methods to measure the following ranges of current and voltage: 50mA, 100mA, 1A, 5V, 50V, and 150V. Draw the circuit diagram of this multimeter with a control switch that can be used to measure either current or voltage.
Input voltage applied to a half wave rectifier is V= 100 cos (150 t). The maximum current through 5kO load resistor is calculated as O a. 10mA O b. 20A O C. 20mA O d. 75mA Next pa Previous page Final exam Descriptive Answer she -Electronics 1 ► Jump to... Forum ciull lis hp
Design a multirange d.c. milliammeter with a basic meter having a resistance 75 ohm and full scale deflection for the current of 2 mA. The required ranges are 0-10 mA, 0-50 mA and 0-100 mA ??
Give a detailed description of an expirment about 'D'Arsonval Meter Movement as DC ammeter'.Support your answer with pictures and examples.
10 K D3 The diodes in the circuit are Silicon with forward voltage of 0.7 V. Fill up the table showing the state, voltage and current of each of the diodes. Show how you validated the state of each diode. Follow the reference shown in determining whether the diode voltages and currents are positive or negative. D1 8 K 5 V 1K D2 f)1 mA Diode State VD İD + Vp D1 すー D2 D3
10 K The diodes in the circuit are Silicon with forward voltage of 0.7 V. Fill up the table showing the state, voltage and current of each of the diodes. ww 8 K D1 Show how you validated the state of each diode. Follow the reference shown in determining whether the diode voltages and currents are positive or negative. 1)1 mA 5 V 1K Diode State VD iD + VD D1 D2 D3