0.063 kg/s of nitrogen is compressed isothermally from 95 kPa and 19°C to 855 kP. in a reversible steady-flow device. Calculate the power required for this compressio, in (hp). Hint: 1 kW = 1.341 hp O 11.5 hp 12.0 hp 190 4 hn

0.063 kg/s of nitrogen is compressed isothermally from 95 kPa and 19°C to 855 kP. in a reversible steady-flow device. Calculate the power required for this compressio, in (hp). Hint: 1 kW = 1.341 hp O 11.5 hp 12.0 hp 190 4 hn

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: calculate total moment at... At point O in this system. 500 N Choose... 3 m Choose.. 2234NM 1060NM…

Q: of the horizontal force P, acting as shown, that will cause motion to impend for the 450-lb crate.…

A: Given Mass, m = 450 lb = 204 kg Coefficient…

Q: enerator has a full-load current of 100A at 220V. Stray losses are 1kW and shunt field current is 12…

Q: Q2) Water flowing through a jet with velocity of 45 m,/s. Caleulate the value of (O) to be the water…

A: Find the angle of jet from the horizontal.

Q: LO2: Perform kinematics analysis of different mechanisms. Q.1 Determine velocity of link 4 using…

A: Given r1=10cm=0.10r2=12 cm =0.12 mθ2=60°ω2=500 rpm Find the velocity link 4

Q: Q 16. In a stressed body, an elementary cube of material is taken at a point with its faces…

A: Find the principal stresses.

Q: A knuckle joint, that shown in the figure below, is used to transmit 250 kN. Considering the various…

A: Knuckle joint is defined as when there is a small amount of flexibility in joining the two rods with…

Q: 24 Problem: Mathematics in Wind Energy Production Wind power is defined as the use of air flow…

A: For plotting matlab can be use. Here i give code and its out put

Q: A circular aluminium rod 12 mm in diameter is loaded with an axial force of 4 kN. What is the…

A: Find the decrease in diameter.

Q: The 50 mm diameter rod has a stress strain diagram as shown. Knowing that the angle of twist is…

Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…

Q: 1. Complete the ideal gas tables. All answers shall be in 4 decimal places. P (kPa) 125 p (kam/m') D…

Q: In a reaction stage of a steam turbine the nozzle angle is 20° and the absolute velocity of the…

Q: calculate total moment at... At point O in this system. 500 N Choose... 3 m Choose.. 2234NM 1060NM…

A: Moment = Force X perpendicular Distance Let Clockwise moment is positive Anti clockwise moment is…

Q: A certain coal has the following ultimate analysis: Carbon = 69% Nitrogen = 5% Hydrogen = 2.5%…

A: Given data A certain coal has a heating value of 27126.16 kJ/kg After ultimate analysisPercentage of…

Q: Q2) Consider a mass (m=5 kg) connected to a massless rod of length (L=2 m) to swing about point O,…

Q: HW. Determine the maximum bending stress location along the beam. at ang 200 m 700 N/m 500 N.m 30…

Q: Determine the tensions in cables AB, AC, and AD.

Q: Question 2 The couple M acts in a vertical plane and is applied to a beam oriented as shown.…

Q: Q1: A centrifugal pump with a 91.5 cm impeller dia. operates at 800 rpm. If the speed is to be…

Q: The rotation of a flywheel is defined by the rotation ω = 2(4t + 1)1/2, where ω is in rad/sec and t…

A: Answer: The angular acceleration of flywheel when t = 5 sec is 1.119 rad/sec2.

Q: In this task, various ideal gases are considered. If no other information is given, the specific gas…

A: Since we only answer up to 3 subparts so we will answer first 3. Please resubmit the question by…

Q: A particle is moving along a curved path. At a certain instant when the slope is 0.75, ax = 2 m/s2…

A: Giventanθ=0.75ax=2m/s2ay=3m/s2

Q: contains a bubble of diameter 1 mm. How much higher is the internal pressure of this bubble compared…

Q: The first stage of a turbine is a two-row velocity compounded wheel. Steam at 40 bar and 400 C is…

Q: R134a enters a reversible adiabatic compressor as a saturated vapor at 10 C. The exit of the…

Q: A Given the following force vectors. F. - 100 N, E; = 7°, 8= 150, {=75° F2 = 150N,Ez=120', Be=cs°,…

A: A resultant force is defined as the single force attained by amalgamate system of forces acting on a…

Q: 3. Calculate the critical load of a strut which is made of a bar, circular in section and 5 m long…

A: As per given question L=5m Deflection of beam =15mm Load=85 We have to find determine critical load…

Q: 9-26 A 0.5-m-long thin heat flux on one side, w air at 5°C. The plate surf midpoint temperature is…

A: mean fluid temp = ( tmid+ text)/2 = 30 degrees

Q: This one may be a bit odd, but I can't seem to locate the proper term for a shaft with two flats…

Q: Question 2 The couple M acts in a vertical plane and is applied to a beam oriented as shown.…

Q: rticle rotates clockwise in accordance with the equation θ = 32 + 24t – 2t3 where θ is in radians…

A: Given:θ=32+24t-2t3

Q: #3. The distributed load w is supported by three suspender bars as shown. AB and EF are made of…

Q: Q 13. A frame is said to be 'Perfect frame, if it followS certain relation betvoen number of members…

A: Perfect frame will not change when it is subjected to load with help of perfect number of members…

Q: Q1) Water flowing through a jet with velocity of 30 m /s. Caleulate the value of (0) to be the water…

Q: Derive the kinetic energy equations and the mass equivalents of the two-system shown.

Q: In an air-conditioning unit 3.5 m3/s air at 27°C dry-bulb temperature, 21°C wet-bulb temperature,…

Q: A pneumatic system is producing 120lb/in^2 of gauge pressure. It has been determined that 7 lb of…

Q: 2. A helical compression spring is made with oil-tempered wire with a diameter of 0.2 in, outside…

Q: 6.. A cantilever beam is 2.5 m long, and carries a concentrated load of 380 N at its midpoint, and…

Q: Consider an aluminum specimen with a diameter of 10 mm and a length of 1 point 3 m. A force of 3000…

A: Find the elongation of the specimen.

Q: A Carnot engine contains 2.00 mol of neon gas as its working substance. It operates with a hot…

A: Solution to first three sub-parts as per our company policy:

Q: The 600-mm pipe shown in Figure 8 conducts water from reservoir A to a pressure turbine, which…

Q: A logging firm in Isabela operates a diesel electric plant to supply its electrical energy…

A: Given data, Mass flow rate of fuel is m˙f=250 gallons/24 hrm˙f=25024×0.85×3.78m˙f=33.47 kg/hr here,…

Q: The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the…

Q: HW. Determine the maximum bending stress location along the beam. at ang 200 m 700 N/m Iso 500 N.m…

Q: QI) Benzene with specific gravity of 0.8 flows through 200 mm diameter pipe at velocity of 5 m/s.…

Q: A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of…

Q: A rectangular plate 3 m x 2 m is immersed horizontal inside a liquid of specific gravity 1.2.…

Q: 3 m -3 m *-3 m 3 m B C 4 m H 10 kN 15 kN 5 kN A) Use method of sections to find the forces in CD,…

Question

0.063 kg/s of nitrogen is compressed isothermally from 95 kPa and 19°C to 855 kPa
in a reversible steady-flow device. Calculate the power required for this compression
in (hp). Hint: 1 kW = 1.341 hp
11.5 hp
12.0 hp
190.4 hp
182.6 hp
O 15.43 hp
O 16.09 hp

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In an experiment , a certain amount of air is heated at constant pressure from 1,7 cubic meters,20 degrees celsius and 97 KPa to 404 degrees celsius. It is then cooled at constant volume back to its initial temperature.Take specific heat at constant pressure and constant volume for air as 1,005 KJ/kg K and 0,717 KJ/kg K repectively. Calculate: 1. the change specific entropy in the cooling process in 1 decimal place and SI unit 2.the change specific entropy in the constant pressure process in 1 decimal place ans SI unit
A pump increases the water pressure from 70 kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 45 oC through a 1.5 cm diameter opening and exits through a 2.1 cm diameter opening. Determine the velocity of the water at the (a) inlet and (b) outlet when the mass flow rate through the pump is 1.4 kg/s. Submit your solution by multiplying (a)*(b) = Format answer : 46.84 Submit
8-96 Air is compressed isothermally from91kPaand32∘Cto550kPain a reversible steady-flow device. Calculate the work required, inkJ/kg, for this compression. Answer:157 kJ/kg
Air is compressed in a cylinder polytropically from an initial temperature and pressureof 84°F and 16 psia to a final of 290°F and 78 psia. The cylinder contains 0.015 lb of air,and has a piston area of 0.18 sq ft. Sketch the process on P - v and T – s coordinates andfind the work done, ft.lbfA. (-)648.41 (on) B. (-)850.85 (on) C. (-)950.85 (on) D. (+)648.41 (by)
Write the expression of heat for an isothermal reversible expansion of a perfect gas from initial volume V1 to final volume V2.
Air is compressed in a piston-cylinder device in a reversible isothermal process at a temperature of 25 C. If the work done by the compressor is 125.4 kJ/kg, the change in the entropy (kJ/kgK) of the system is Select one: -0.421 -0.528 -0.429 -0.544
An air compressor compresses atmospheric air at 0.1 MPa and 27°C by ten times of inlet pressure. During compression, the heat loss to the surrounding is estimated to be 5% of compression work. Air enters the compressor with a velocity of 40 m/s and leaves with 100 m/s. Inlet and exit from cross-sectional areas are 100 cm? and 20 cm? respectively. Estimate the temperature of air at exit from compressor and power input to the compressor. (1498 K, 5467.86 kW)
Air (MW=29 kg/kmol) at 115.00 kPa and 285.00 K is compressed steadily to 600.0 kPaThe mass flow rate of the air is 2.00 kg/s and a heat loss of 32.1 kW occurs during the process. You may assume that changes in kinetic and potential energy are negligible, the temperature of the surroundings is 25 ∘C and that the CP of air is 3.5 R. Given the compressor operates with a second law (reversible) efficiency of 0.60, calculate the following. What is the actual work interaction term? What is the actual exit temperature of the air?
A 4-kg steel rod 873°C (specific heat= 0.85kJ/kg-K) is annealed in a cylindrical tank 3B0 kg of water originally at 20°C during a heat-treating process. What is the closest approximation to the overall entropy change of the system after annealing?
There are 60,000 kcal/hr of heat extracted from 5.67 kg/s of carbon monoxide gas whie the temperature remains constant at 28°C The initial pressure is 600 kPaa. For both nonflow and steady flow (AP = 0, AK - 0) process, determine the change in entropy in kW/K. 0-423 O 012 O 034 O 023 O034
A vessel containing 63.8 kg of water is left out where it evaporates completely. Assuming the temperature remains con- stant at C, what is the change in entropy? The latent heat of vaporization of water at 20°C is 585 cal/g. Answer in units of kcal/K.
A constant volume closed container, It is divided into two equal compartments by a metal curtain. Initially 2.5 kg of compressed liquid water at 400 kPa pressure and 60 ° C temperature in ones of the compartment, the other is vacuum are available. Then the metal curtain is removed and water fills the entire volume. Finally in the container as the pressure is 40 kPa, Calculate the entropy change (kJ / K) of water during this process.