(1) (2) P A В C 0.45 m 1.30 m The assembly above starts out at 52 degrees celsius. What is the final position of C after a load of P = 10 kN is applied and the temperature is cooled to a final temperature of 30 degrees celsius? Enter distance C moves in mm into D2L answer box. In Pdf, be clear if it moves to the right or the left. Assume the following: (1) Bar AB is 60mm x 6 mm thick, E = 65 GPa, az = 9.5 x 10*/rc. (2) Bar BC is 20mm in diameter, E = 170 GPa, az = 7.5 x 10®pc. Your AnswNer:

(1) (2) P A В C 0.45 m 1.30 m The assembly above starts out at 52 degrees celsius. What is the final position of C after a load of P = 10 kN is applied and the temperature is cooled to a final temperature of 30 degrees celsius? Enter distance C moves in mm into D2L answer box. In Pdf, be clear if it moves to the right or the left. Assume the following: (1) Bar AB is 60mm x 6 mm thick, E = 65 GPa, az = 9.5 x 10*/rc. (2) Bar BC is 20mm in diameter, E = 170 GPa, az = 7.5 x 10®pc. Your AnswNer:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

• What is the member force in CD? Indicate the negative (-) sign in your answer if the member is in compression. 12k 18 k 12 t D 36° 25 k 20 ft 16 ft
Two rods vertically connect beams AB and CD as shown in the figure. Point A is fixed supported while point D is hinged connected. If the rod on the right is heated by 10 degree Celsius, 2 m 2 m 2 m C Use E- 200 GPa, linear of coefficient expansion-11.7x 10° per degree celsius and A = 4500 mm2 Compute for the deformation of the right rod in mm. Select the correct response: 0.0234 mm 0.0842 mm 0.0468 mm
A HA He 1 m L 1 m
Two rods vertically connect beams AB and CD as shown in the figure. Point A is fixed supported while point D is hinged connected. If the rod on the right is heated by 18 degree Celsius, 2 m- - 2 m A 2 m C Use E = 200 GPa, linear of coefficient expansion = 11 7x 10 per degree celsius and A = 4500 mm2 Compute for the deformation of the right rod in mm. Select the correct response 0.0468 mm 0.117 mm 0 0234 mm 0.0842 mm
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. 5P E-10 GPa + 39 E-200 GPo 3M 80mm 30 mm 30mm 80 mm 30 mm 30 mm
2 Poin Question 7 of 15 The steel plate shown below is put in into a rigid chamber, such that spacings of size s = 0.00188 m. To fit the plate, it is heated. It can be assumed that the plate can move frictionless along its edges. If x 4 m and y=2m, E = 200 GPa V = 0.28 a = 11.7 x 10 rc For which temperature increase along the y-axis is the upper spacing just closing in degree celsius? Select the correct response
4. A copper bar 250 mm long and 50mmx50mm in cross-section is subjected to an axial pull in the direction of its length. If the increase in volume of the bar is 37.5 mm', find the magnitude of the pull. Take p-0.25 and E-100GPA. Answer: P-30 KN. 5. A steel bar 50mmx50mm in cross-section is 1.2 m long. It is subjected to an axial pull of 200 KN. What are the changes in length, width and volume of the bar, if the value of Poisson s ratio is 0.3 ? Take E as 200 GPa. Answer Al-0.48mm, Ab-0.006mm and AV-480 mm'. 6. A reetangular bar 500 mm long and 100mmx50mm in cross-section is subjected to forces as shown in figure. What is the change in the volume of the bar? Take modulus of elasticity for the bar material as 200 GPa and p-0.25. Answer :AV-137.5 mm'. 300 KN 100 KN 50 100 200 KN 500 mm
3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and carries the load of 110 kN. The system is stress free before the load is applied. After the load was applied, the temperature of all wires is raised by 20°C. Use a = 12x10-6/°C for steel, a = 18x10-6/°C for copper and a = 20x10-6/°C for brass. Neglecting the weight of the bar AB, determine the location of the 110 kN force in order that AB remains horizontal. copper bar: A=195mm? steel bar: brass bar: A=130mm? A=325mm? A C B 110 kN 3.00m 2.00m 1.80m _ 1.20m 1.50m
QUESTION 3. A simply supported beam, having notches on its surface, is subjected to a triangular distributed load as shoen in the figure. The factor of safety is defined to be 1.5 for yielding. Calculate the maximum value of wo that the beam can support. The notch radius is 10 mm. 10 mm Wo 50 mm 40 mm Losmtosm- 0.5 m -0.5 m -0.5 m
Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the figure below where the horizontal force P = 210 N and the couple M = 527 Nm. 90 N 250 mm 150 N 400 mm M&N•m A 300 P
е Q2). A 20m steel tape supported at both ends was used to measure horizontal P distance of CD at a temperature of 35 °C and 60 N tension force measured distance was 350m. Under the standard conditions was found that the tape 19.95m length. Find the actual horizontal distance between CD if: Ts Standard temperature 25 °C Coefficient of thermal expansion of steel tape = 11.6x10-6/°C Po Standard tension = 100N. Modulus of elasticity (E) = 210 kN/mm² Cross-sectional area of the tape = 2 mm² The weight of this tape between supports 8 N
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa Aluminum L=2m A=500mm 2m 2m E-72Mра P=20KN