1) Calculate the maximum RMS current in p.u. that guarantees the equality of losses between the deformed and non-deformed regime for a power transformer equal to 400 kVA with Pcp = 6% in two cases: a) the transformer feeds a twelve-phase converter Idc=40 A b) the transformer feeds a six-phase converter Idc=40 A.

1) Calculate the maximum RMS current in p.u. that guarantees the equality of losses between the deformed and non-deformed regime for a power transformer equal to 400 kVA with Pcp = 6% in two cases: a) the transformer feeds a twelve-phase converter Idc=40 A b) the transformer feeds a six-phase converter Idc=40 A.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1