شباب اريد حل هذني We can construct it by using diodes and resistors as following withits truth table:1k Ohm isvA Y0 11 0IkOhmDIGITAL LABFirst stageDiscussion :1- Draw AND gate and OP ate with three inputs by usingdiode nsistor and sistor ?Draw the following equa on by using diode , transistorand resistor ?1- A.B + A.B2- A.B.C+D3- (A.B).(C.D)

Answered: 1- Draw AND gate and OPcate with three…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

G2/.Design Circint as the following peseripton: A- the positive Cycle of the vout signal is 3.2 and Negative cycle is 4-33 (Note: we must used preetical Diodes and vin is lov) 13- the positive cyclep of vout is s.3 ond Negative cycle is (5.4) [Note:consider vin = tovavd we must used Capaetor with praeticul Didde)
A clamper circuit has 20 Vp-p. 100Hz square wave input voltage. The circuit consists of silicon diode IN4001 and 3V battery as shown in Figure 1 C. 0.1 µF D R Vi(t) 50 k2 Vo(t) 3 V Figure 1 a) Find the output voltage for all input voltages values. b) Sketch the output waveform, Vo(t).
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
After replacing R5 with diode IN4007 (switch K3 to diode side) .What conclusion can you draw from analysis of this step ?
Given the following circuit with VDD = 5 V, R = 2.6 k, then the current Iis: Use the CVD model for the diode, with VD= 0.65 V. V DD I a. 0.001673 A O b. 0 A O c. 1.673077 A O d. 1.923077 A e. 0.001923 A R + VD -
Using an ideal diode, design a clamper circuit that result in the desired output waveform as shown in Figure Q7. Show overall analysis to justify the proposed design. 7. Vo Vi Designed Clamper Circuit - 3 V -20 - 43 V - Fiqure Q7 20
What is the output voltage across a load resistor if it is paralleled with a forward biased silicon diode? The resistor network is supplied with 10 V. * O A. 0.7 V O B. 9.3 V O C. 10 V O D. Can't be solve, lack of data.
I need some help with this problem. I need to create a power supply from 110v 60hz to regulated an output between 6 and 9 v. the image is the desire circuit to acomplish the possible solution. The resistor after the bridge rectifier will work as a surge protector or current limiter for the zener diode. the other is the Load resistor. I need some sort of calculations to prove the specific values for the components to operate according to the specs that I already explain. I know the capacitor will smooth the ripple voltage etc... but I need some guidance to get actual values
V, is a 60Hz source with a peak voltage VP-120V is feeding a rectifier, assume ideal diode. The load resistance has a value of R= 10 k0. If ripple voltage Vr = 2V, the Diode average current Ipavg is VI Select one: a. + e. None Ob. 580mA Oc. 850mA Od 245mA 425mA D C: www tu Vo Q6
G2/A.Design Circint as the following pereripton: A- the positive Cycle of the vant signal is 3.2 and Negative cycle is 4.3 (Note: we must used praetical Diodes and vin is tov)
Given the following circuit with VDD= 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. I VDD a. 0.004000 A O b. 3.717391 A OC. 0 A d. 4.000000 A e. 0.003717 A R + VD -

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

1- Draw AND gate and OPcate with three inputs by using diode nsistor and sistor ? Draw the following equa on by using diode , transistor and resistor ? 1- A.B + A.B 2- A.B.C+D 3- (A.B).(C.D)