1) Suppose that, instead of using NaOH, a base such as Ba(OH)2 had been used. What changes in the calculations would then have to be done to determine the molar concentrations of the base? Answer this question in words, and illustrate your answer by calculating molarity from the following data: mol KHP used 0.040 mol Ba(OH)2 Initial buret level = 0.020 mL Final buret level 36.70 mL

1) Suppose that, instead of using NaOH, a base such as Ba(OH)2 had been used. What changes in the calculations would then have to be done to determine the molar concentrations of the base? Answer this question in words, and illustrate your answer by calculating molarity from the following data: mol KHP used 0.040 mol Ba(OH)2 Initial buret level = 0.020 mL Final buret level 36.70 mL

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter14: Acids And Bases

Section: Chapter Questions

Problem 127QRT

See similar textbooks

Similar questions

Does the pH of the solution increase, decrease, or stay the same when you (a) Add solid sodium oxalate, Na2C2O4, to 50.0 mL of 0.015-M oxalic acid? (b) Add solid ammonium chloride to 100. mL of 0.016-M HCl? (c) Add 20.0 g NaCl to 1.0 L of 0.012-M sodium acetate, NaCH3COO?
Questions 11-14 refer to the same strong base/strong acid (SB/SA) titration. A 15.00 mL solution of 0.100 M sodium hydroxide (NaOH) is being titrated with 0.250 M hydrobromic acid (HBr). What is the solution pH when 10.00 mL of HBr have been added? (Two decimal places) Type your answer...
Classify the following solutions as one of these types AND calculate the pH: strong acid, strong base, weak acid, weak base, buffer, neutral salt. a) 0.040 M NaF (Ka for HF = 7.2 x 10-4) b) 10 M HClO4 c) A solution made by mixing 10.0 mL of 0.072 M NaOH with 15.0 mL of 0.100 M acetic acid (pKa for acetic acid = 4.75) d) 0.453 M NaCl
Answer the following three questions based on the information given below. Consider a buffer made with 34.0 mL of 0.25 M butanoic acid (HC4H-O2) and 16.0 mL of 0.46 M sodium butanoate (NAC4H7O2). The K, for butanoic acid (HC H-O,) is 1.5 X 10 5. Round all numerical answers to the 100en place (2 decimal places). Assume 298 K. What is the pH, if 20.0 mL of 1.0 M NAOH is added to this buffer? Type your answer..
This question is about acid base titration: Osama a student, performed an acid base titration involving a standard solution of Sodium hydroxide (NaOH) (RMM = 40) against unknown HCl solution and obtained the following results. Mass of Sodium hydroxide (NaOH) dissolved in 250 ml volumetric flask = 3.6 g 2.Volume of Sodium hydroxide used in the titration = 23 ml 3.The mean volume of HCl titrated with 25 ml Sodium…
5 What volume, in milliliters, of 0.240 M NaOH should be added to a 0.135 L solution of 0.030 M glycine hydrochloride (p Kal = 2.350, pKa2 = 9.778) to adjust the pH to 2.78? 5 NaOH volume = mL
Consider 100 mL of 0.10 M Ba(OH)2 (solution 1) and 0.10 M NaOH (solution 2), which of the following statement/s is/are TRUE? pH (solution 1) = the pH (solution 2) pH (solution 1) > pH (solution 2). % ionization (solution 1) = % ionization (solution 2) % ionization (solution 1) > % ionization (solution 2) I and III II and IV II and III I and IV
An intrinsic property is one a That is dependent on how much of the material is present That is analogous to the flammability of any substance That is analogous to the flammability of any substance That only changes withaltitude How many moles are in 20 mg of steric acid, CH_3(CH_2)_{16}COOH?
EXPERIMENT K Acid-Base Titration: How Much Acid Is In Vinegar? Discussion The label on the bottle of commercial vinegar states that it contains 5.0% acetic acid. According to your calculations, has the manufacture truthfully reported the percent of acetic acid in vinegar? Support your answer with data. 1. 2. A grocery store sells vinegar in 1-L bottles. Based on your answer to question 4 on the previous page. how many moles of acetic acid are in a 1-L bottle of vinegar? a. 60.9 if 10.00 mL of b. how many grams of acetic acid are in a 1-L bottle of vinegar? 6.0 9 3. Would the calculated molarity of acetic acid in vinegar be diluted vinegar had been used in place of the 15.00 mL sample. Explain your answer. a. the same D, higher С. lower 4. If you over-titrate, a significant error will occur in your calculations. Determine how each of the following values would be affected if you over-titrate? Circle the cor- rect response. The volume of NaOH recorded to reach the equivalence point would…
Suppose your laboratory instructor gave you a sample of KHP contaminated with NaCl to standardize vour NaOH in the first part of Experiment 15. Which of the following statements are true (select all that apply)? The volume of NaOH(aq) required to reach the equivalence point would be larger than if the contaminant were not present O The volume of NaOH(aq) required to reach the equivalence point would be smaller than if the contaminant were not present The volume of NaOH(aq) required to reach the equivalence point would not be affected by the contaminant The molarity of the NaOH would be higher than the correct molarity The molarity of the NaOH would be lower than the correct molarity The molarity of the NaOH would be unaffected (same as the correct molarity) O O O
Questions 11-14 refer to the same strong base/strong acid (SB/SA) titration. A 15.00 mL solution of 0.100 M sodium hydroxide (NaOH) is being titrated with 0.250 M hydrobromic acid (HBr). What is the solution pH before the titration begins? (Two decimal places) Type your answer...
(a) Calculate the pH in the solution formed by adding 10.0 mL of 0.050 M NaOH to 40.0 mL of 0.0250 M benzoic acid (C6H5COOH, Ka = 6.3 * 10-5). (b) Calculate the pH in the solution formed by adding 10.0 mL of 0.100 M HCl to20.0 mL of 0.100 M NH3.