1. Given a theoretical solar cell with open circuit (no load) output voltage of 0.55V and ideal diode parameter Io=2x10-11 A (for some certain sunlight conditions). a. What is the internal diode current, equal to the solar current when there is no load? b. Assuming the solar current stays the same as found in (a), what is the load current and output voltage when a 100 Ohm load resistor is connected? c. Assuming the solar current stays the same as found in (a), what is the load current and output voltage when a 10 Ohm load resistor is connected?

1. Given a theoretical solar cell with open circuit (no load) output voltage of 0.55V and ideal diode parameter Io=2x10-11 A (for some certain sunlight conditions). a. What is the internal diode current, equal to the solar current when there is no load? b. Assuming the solar current stays the same as found in (a), what is the load current and output voltage when a 100 Ohm load resistor is connected? c. Assuming the solar current stays the same as found in (a), what is the load current and output voltage when a 10 Ohm load resistor is connected?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

5. Suppose we are given a pn diode, and we apply the applied voltage Vapp to the n-type and ground the p-type. In this case, we would consider positive current I to point from the voltage source node to the ground node. Under these conditions, plot I vs. Vapp for the diode, and label three points representing zero bias, forward bias, and reverse bias. Between a forward bias of 0.65 V and 0.75 V, what multiplicative factor increase do we expect in 1? I Vapp
In the circuit shown in the figure, diode voltages are given as 0.6V and rD = 100 ohms. When point B is open circuit AIf + 5V is applied to the point of application, drawing the shape of the circuit formed and calculating the currents passing through the resistors.calculate.
A silicon diode has 1 ampere DC of current in biasd mode. What is voltage drop across the diode?
In the circuit given in the figure, since Vi is a square wave with a frequency of 1 kHz and an amplitude varying between +5V and -5V; Vi and Vo voltages one after the other and in scale; a) Draw with Zener diode is not active ? b) Draw with the Zener diode on? (Assume the diodes in the circuit are ideal)
5) The figure below illustrates a simple voltage threshold detection circuit. To understand how it operates, we will analyze its behavior based on the simple constant voltage drop model for both diodes. Assume the Zener diode (Z1) only conducts when its breakdown voltage of 10V is reached. Di is a red light emitting diode (LED). Assume it conducts after its forward bias voltage of 1.8V is reached. Vin is unknown. Assume Zj acts as a perfect Zener diode (without series resistance). What voltage does Vin have to reach before there is a current through R¡? What voltage must Vin reach before current flows through R2? Write an equation for the current through Zi in terms of Vin, Rị and R2 that is valid when Vin is high enough for both diodes to be conducting. a. b. c. R2 Vino R1 LED
There are three diode models namely (i) the exponential, (ii) ideal and (iii) the constant voltage source. a) Please define each model and provide the factors that influence the choice of a diode model when analyzing a circuit ? b) Please provide sketches of the I-V characteristic of each model.
For the circuit in the figure below, in which the diode has a value Vd = 0.7 V: Calculate the two values of Vout. Calculate the value of Vin that will cause Vout to change between the two levels found in part a). Sketch the signal Vout. Include values for time and voltages.
Current measured in the circuit in the shape created using the ideal diode model .....is. Please select one: a. 0.87 mA b. 1.2 mA c. 0.80 mA d. 0.73 mA
What is the resistance in the forward-conduction region of the shockley diode based from the problem. No need to compute for the current.
Given the clamper circuit below, assume that the value of R and C are large enough sothe voltage across the capacitor does not change significantly during the interval of time.a. Using the simplified diode model, simulate the action of the circuit when the Silicon diode isin forward and reverse bias condition and measure the corresponding output voltage.b. Draw the complete output waveform of the circuit
In this circuit, what will be the voltage peaks of the output, if the input is 20Vp-p sine wave?Note: Use First Approximation/ideal diode model. (+peak, -peak)The choices are: A. 10V, 10V B. -3V, -23V C. 3V, -17V D. 23V, 3V
A zener diode of voltage Vz( 6 volt) is used to maintain a constant voltage across a load resistance RL( = 10000) by using a series resistance Rs(+1000). If the emf or source is E( = 9V), calculate the value of current through series resistance, zener diode and load resistance. =