1.Two identical shunt generators running in parallel, each with armature resistance of 0.02 ohms and field resistance of 50 ohms. The combined load current is 5000A. The field are so excited that the generated voltages of one machine is 610V and the other is 600V. The terminal voltage of this parallel combination will be. www $ Rh1 a.350-360 V b.450-460 V c. 550-560V Rat az G₁₂ Raz 5000 A Ish2

1.Two identical shunt generators running in parallel, each with armature resistance of 0.02 ohms and field resistance of 50 ohms. The combined load current is 5000A. The field are so excited that the generated voltages of one machine is 610V and the other is 600V. The terminal voltage of this parallel combination will be. www $ Rh1 a.350-360 V b.450-460 V c. 550-560V Rat az G₁₂ Raz 5000 A Ish2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

What are the conditions in paralleling of these DC Generators:a. Shuntb. Seriesc. Compound
The primary of a certain transformer takes 1 A at a power factor of 0.4 when connected across a 230 V, 50 Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. Sketch, and explain briefly, the phasor diagram for this condition, neglecting voltage drops in the transformer. What is now the value of the primary current?
5. Two shunt generators A and B operate in parallel and their load characteristics may be taken as straight lines. The voltage of A falls from 240 V at no-load to 220 V at 200 A, while that of B falls from 245 V at no-load to 220 V at 150 A. Determine the current which each machine supplies to a common load of 300 A and the bus-bar voltage at this load.
The primary ofa certain transformer takes 1 A at a power factor of 0.4 when connected across a 230 V, 50 Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. Sketch, and explain briefly, the phasor diagram for this condition, neglecting voltage drops in the transformer. What is now the value of the primary current?
The terminal voltage of a 150 kW series generator is 600 V at rated load. The armature resistance is 0.06 ohms and the series field resistance is 0.04 ohms. Find generated emf.
Two shunt generators A and B operate in parallel and their load characteristic s may be taken as straight lines. The voltage of A falls from 240 V at no - load to 220 V at 200 A, while that of B falls from 245 V at no - load to 220 V at 150 A. Determine the current which each machine supplies to a common load of 300 A and the bus - bar voltage at this load.
O What is the difference between AC and DC coupling?
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 220 V (RMS), 50 Hz. The delay angles of both thyristors are set to 90 degrees. The maximum power that can be delivered to the load is: Select one: a. 5.65 kW b. 9.68 kW c. 11.52 kW d. None of these
Two shunt generators A and B operates in parallel and their load characteristicsmay be taken us straight lines. The voltage of the generator A falls from 240 V atno-load to 220 V at 200 A while that of B falls from 245 V at no load to 220 V at150 A. Determine the current which each machine supplies to a common load of300 A and the bus-bar voltage at this load.
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
Q3/ A/ Compare between de series and shunt generator. Q3/ B/ Briefly explain the commutating process in dc machine.
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source