19.a. Which term relates to the conductors connected to the output side of a separately derived system? A. System conductor B. Derived phased conductor C. Transformer secondary conductor D. Neutral conductor 19.b. Overcurrent protection for a separately derived system must be located immediately adjacent to the A. disconnecting means. B. site-isolating device. C. grounded conductor. D. junction box

19.a. Which term relates to the conductors connected to the output side of a separately derived system? A. System conductor B. Derived phased conductor C. Transformer secondary conductor D. Neutral conductor 19.b. Overcurrent protection for a separately derived system must be located immediately adjacent to the A. disconnecting means. B. site-isolating device. C. grounded conductor. D. junction box

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.16MCQ

See similar textbooks

Similar questions

c.1. Which of the following is one of the three essential functions of an equipment grounding conductor?A. Provide an arc-fault current pathB. Establish groundingC. Establish bondingD. Ensure the system is groundedc.2. What's another name for the three-point method of Earth resistance testing?A. Fall-of-potentialB. Line surgeC. Spatial shieldingD. Leakage current c.3. If the National Electrical Code provides a requirement to ground equipment, it generally implies thatthere will be a direct connection to the Earth of a connection through a/anA. grounding electrode conductor.B. equipment grounding conductor.C. equipotential bonding conductor.D. bonding conductor.
15. Which of the following conductors in a typical separable connection plug and receptacle has a firstmake, last-break feature?A. The neutral grounded conductorB. The equipment grounding conductorC. A center wye conductorD. The grounded delta conductor
18. Which part of a lightning protection system is at the top of the structure?A. Ground terminal networkB. Down conductor networkC. Strike termination networkD. Equipotential bonding network
12. If overcurrent protection is provided in the transformer of a separately derived system, which of the following statements is correct?A. A ground electrode must be present at the transformer and the building's disconnect.B. There's no need for service equipment or a panelboard in the separate building.C. An equipment grounding conductor must be run with the conductors between the transformer and the building's disconnect.D. The neutral should be bonded to the equipment grounding conductor at the service equipment in the separate building.
Which of the following Surge Diverter use non-linear resistances in its fabrication? Rod - Gape SD. Lightning Arrester SD. Expulsion Tube SD. O All of the above.
4. What can installation records be used to determine while servicing equipment?A. Broken connectors in a cable linkB. Problems due to aging during operationC. Broken fiberD. Decreased bending radius during operation
b) Why Generation Voltage Levels are low in the range of 11 kV/ 33 kV etc? c) Why ACSR Conductors are preferred over Copper Conductors?
7.B. The size of a grounding electrode conductor for a service or separately derived system is generally basedon the size of the largestA. ungrounded supply conductor.B. equipment grounding conductor.C. grounded electrode.D. bonding jumper.7.C. Which of the following statements about bonding is true?A. The joint or termination must offer opposition in the circuit for effective electrical connections.B. Effective bonding keeps impedance high if a fault should occur.C. The entire electrical safety circuit is only as good as its strongest bonded link.D. Bonding connections must endure high levels of fault current until overcurrent protective devices can operate.
A.1. How many normally open auxiliary relay contacts are shown in the schematic diagram in Figure A7?A. 2 B. 3 C. 1 D. 0 A.2. What type of diagram is shown in Figure A7?A. Three-line schematic diagramB. Block diagram C. Wiring diagram D. Single-line ladder diagram A.3- What type of component is labeled A in figure A7?A. oil-type breaker, B. auxiliary contact, C. Normally closed breaker, D . NC pressure switch
Explain prevention of Arc restriking Theories in circuit breaker.
For grounded systems, the _ for the service and the system bonding jumper for separately derived systems provides the critical link between the equipment grounding conductor and the grounded system conductor. A.main bonding jumper B.Service transformer C. Current transformer D. Grounding electrode
What is a grounding conductor? What is a grounding conductor (equipment)? What is a grounding electrode conductor? What is an outlet?