2) Consider the multi-stage amplifier shown below. Determine Vin if Vo = 3.3V. Because ₂ is so small and le2 is so large, do NOT assume that Ib=0 and do NOT assume that I le Assume that both transistors are in Forward Active and each is described as follows: Q1: B₁ = 100, VBE(ON) = 0.7V Q2: B₂ = 14,VBE (ON) = 0.7V 10V Vin 10V T 2K Q1 500 V01 Q2 220 Vo

2) Consider the multi-stage amplifier shown below. Determine Vin if Vo = 3.3V. Because ₂ is so small and le2 is so large, do NOT assume that Ib=0 and do NOT assume that I le Assume that both transistors are in Forward Active and each is described as follows: Q1: B₁ = 100, VBE(ON) = 0.7V Q2: B₂ = 14,VBE (ON) = 0.7V 10V Vin 10V T 2K Q1 500 V01 Q2 220 Vo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Two PNP transistors are connected to form a Darlington pair to create a single stage amplifier. Both transistors have the same B. Assume that is large such that 3+ 1 ~ B. Vcc 028² 028 9m2 RL 2+9m2 RL VIN PNP Darlington Pair Used as an Amplifier 1. If the Darlington pair is to be treated as a single transistor, what is the overall 3 if the "emitter current" is IOUT? OB² 9m2 Rp 1+9m2 RL RL 9m2 RL iOUT 2. Calculate the approximate expression for Ay. User1 and gm1 for the parameters of Q1 while 2 and for the parameters of Q2. Assume VA → ∞ for both transistors. 9m2 -9m2 RL 2 VOUT
Q.1/ Figure below shows a CE power amplifier in which the collector resistor serves also as the load resistor. Assume Boc-Bac-100. a. Determines the de Q-point (Ico and VCEO). b. Determine the voltage gain and the power gain. c. What changes would be necessary to convert the circuit to a pnp transistor with a positive supply? What advantage would this have? +Vce +15 V R 100 LO K 0.5 W 22 juF RE 8.2 S00 mV pp 330 1 R 36 0 100 uF
2) Consider the multistage amplifier shown below. Assume that the transistors shown are in forward active and described as follows: Q1: ₁100.00, VBE1 = 0.900 V Q2: ₂20.00, VBE2 = 0.900 V Determine Vin if Vo = 6.0V. DO NOT assume that le=lc and DO NOT assume that lb = 0. Show your work! Vin 10V 2.8k Q1 1k V01 10V 200 R 100 Vo
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
1. N-channel enhancement MOSFET control voltage is applied at the controlling the current that is the drain terminal Select one: a. source, entering b. gate, entering C. drain, entering d. source, leaving e. gate, leaving f. drain, leaving 2. In a common source amplifier, the input is fed to the while the output is taken from the Select one: a. source, gate b. source, drain C. gate, source d. gate, drain e. drain, source f. drain, gate 3. In the saturation region of a MOSFET, choose all of the equations that apply (Hint: there are 3) Select one or more: a. VGS >= VTH b. VGS = VGS- VTH g. VDSVGS- VTH ID-k[(2(VGS-VTH)VDS-VDS²]
The n-channel JFET and the D-MOSFET have very similar I-V output characteristics. Which of these two structures can be operated in enhancement mode and why is that possible.
The amplifier in the circuit below is driven by a signal generator v, with a small sine wave signal vhose average value is zero. Assume the transistor has a value of B-100, and V-26 mV. a. You need to design the circuit so that the de emitter current IE of the emitter resistor RE to establish the desired de emitter current. = 1 mA. Specify the value b. A de collector voltage of +5 volts is desired. Specify the value of the collector resistor Re to establish the desired de collector voltage. For this part assume that RL 5 K and the Early Effect needs to be considered. The transistor has a VA 100 Volts. Draw the ac small signal equivalent circuit model of the amplifier and determine its voltage gain. 91SV C. 2.5k MM do RE -15 V 84 Vout RL
4. A Darlington transistor is essentially an array of two transistors connected as shown below. Assume both transistors follow our simple model with a current gain of B=100. Determine the maximum value of R2 that will just saturate the transistors, and pass full current through the load resistance R1. v2 V2 R2 PULSE (0 5 0) Q2 NPN R1 10 Q1 NPN V1 24
circuits by using the small signal models of the transistor. Assume the Early voltage of the transistors are infinitely large. Calculate the small-signal input and output impedances of the following Vcc R1 R1 Rout VB RE Rin R2
Q.1/ Figure below shows a CE power amplifier in which the collector resistor serves also as the load resistor. Assume Boc=Bac=100. a. Determines the de Q-point (Ico and VCEQ). b. Determine the voltage gain and the power gain. c. What changes would be necessary to convert the circuit to a pnp transistor with a positive supply? What advantage would this have? RL 100n 05 W LOk 22 uF RE 8.20 s00 mV pp 330 1O KHz 36 f1
For the given Common Emitter NPN Amplifier, the transistor made of Germanium diodes, BDC-80, Vcc Rc-3.9 K2, RE-0.68 KQ. a) Name the type of biasing used in the above circuit? 1 = 16 volts, R= 62 KQ, Rz 9.1 K R, Rc Cs b) Find VE? Find VCE? d) Find Vc? e) What is the name of the capacitors C1, C3 and C2?
Design-CE255/ purses / Introduction to Electronic Analysis and Design - CE255/E To use it as an amplifier Select one: a. The MOSFET should in the triode region b. The MOSFET should be in the cutoff region c. The MOSFET should be in the saturation region d. The MOSFET could be in saturation or triode region ge Esessment CE255/EE255 (O1) - Dr. Mamoun Al-Mistar Jump to...