2. A device, as shown in Figure I, can be modeled as a current source in parallel with a resistance. The device exhibits the behavior shown in the plot in Figure 2. Two identical versions of the device are connected in the circuit in Figure 3. The polarity of the device in the two locations is shown with Al and A2 connected to terminal A of the device, and Bl and B2 to terminal B of the device, for the two inserted devices. All resistances are given with units of [Ohms]. a) Find a model for the device, and draw it, showing numerical values for the components. and labeling terminals A and B. b) Find v c) Find the power delivered by the 6.8[mA] current source in Figure 3.

2. A device, as shown in Figure I, can be modeled as a current source in parallel with a resistance. The device exhibits the behavior shown in the plot in Figure 2. Two identical versions of the device are connected in the circuit in Figure 3. The polarity of the device in the two locations is shown with Al and A2 connected to terminal A of the device, and Bl and B2 to terminal B of the device, for the two inserted devices. All resistances are given with units of [Ohms]. a) Find a model for the device, and draw it, showing numerical values for the components. and labeling terminals A and B. b) Find v c) Find the power delivered by the 6.8[mA] current source in Figure 3.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

What is the voltage across the 50 Ohm and 5 Ohm resistors? Using the loop hole equation, what is the voltage across the R1? What is R1?
The diagram in the figure shows a simple circuit consisting of a battery and a load consisting of two resistors.The battery voltage is UB = 56 V and the value of the resistors is:R1 = 1800R2 = 5400a) The ammeters in the circuit show the following value:A1 shows valueA2 shows valueA3 shows valueb) In the load, the effect developsc) The total resistance of the load is
A dc generator and a battery are connected to a resistive load RL in the figure below. For each, determine the value of RL for maximum power transfer to RL. Next is to determine RL to 75% efficiency
A charger, a battery and a load are connected in parallel. The voltage across the charger is 12.5 volts and the battery has an emf of 12 volts and the internal resistance of 0.1 ohm. The load of 2 ohms resistor. Find the current through the charger.
A secondary cell having an e.m.f. of 2V and an internal resistance of 1 ohm is connected in serieswith a primary cell having an e.m.f. of 1.5V and an internal resistance of 100 ohm. The negativeterminal of each cell is connected to the positive terminal of the other cell. A voltmeter having aresistance of 50 ohm is connected to measure the terminal voltage of the cells. Calculate the voltmeterreading and the current in each cell.
is made from a combination of A mixed resistors circuit as shown in Figure parallel and series circuits. The values of the resistances mentioned in the circuit are in Ohm (2) and the supply voltage is in Volt (V). Determine the: (i) Current through the circuit (I). (ii) Voltage drop (V) across the circuit. 0.6 0 4 0 0.5 0
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
Measure the voltages across R1, R2, and R3. Then add the voltages across each element with respect to their polarities around each loop and show your calculations.
calculate the Load current and Load voltage of the given figure
What is the difference between the cut-off voltage VGS0 f and the narrowing voltage Vp? Explain this with the diagram
How do you find the current that passes through the 1 Ohm resistor if there are two junctions? Do we have to use the Kirchoff's Junction Rule and/or is there another way?
A charger , a battery and a load are connected in parallel. The voltage across the charger is 12.5 volts and the battery has an emf of 12 volts and internal resistance of 0.1 ohm. The load consists of a 2 ohms resistor. Find the current through the charger.