2. The cantilever footing is used to support a wall near its edge A so that it causes a uniform soil pressure under the footing. Determine the uniform distribution loads Wa and Wb, measured in Ib per ft at pads A and B, necessary to support the wall forces of 8000 lb and 20000 lb. 20 000 lb 8000 lb - 0.25 ft 1.5 ft B Fint WB -8 ft -3 ft-

2. The cantilever footing is used to support a wall near its edge A so that it causes a uniform soil pressure under the footing. Determine the uniform distribution loads Wa and Wb, measured in Ib per ft at pads A and B, necessary to support the wall forces of 8000 lb and 20000 lb. 20 000 lb 8000 lb - 0.25 ft 1.5 ft B Fint WB -8 ft -3 ft-

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.65P: Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero,...

See similar textbooks

Similar questions

Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero, compute (a) the maximum tensile force in the cable; and (b) the length of the cable.
Q2): Body A is weight 100 N and tied to a rigid wall using a steel cable and it is located on body B of weight 300 N which rest on a rough surface (coefficient of fraction is 0,3). If the fraction coefficient between body A and B is equal to 0.25 and the pulling force P= 600 N. calculate the tension force of the steel cable. A 530 37 B TTTTTT
N and Determine the force in cables N necessary to support the 12 kg traffic light shown in figure. (Hint: Please just enter the numerical value without any unit and use three significant digit only. For example if AB= XXX N then enter only XXX.) Answer. = 24 1.63// KSI. 12⁰ B
Determine the force in each member of the truss loaded as shown below. Indicate whether the members are in tension or compression. Summarize your analysis by filling-up the table shown. 1. 300 kN Summary: 3 m Member Internal Force (KN) B АВ E AE BC 5 m 400 kN ВЕ CD CE DE 3 m-3 m
What would be the resultant force F of the triangular distributed load and its location d measured from point A. 150 lb/ft -3 ft < 5 ft 2 ft Select.one: a F-375 Ib and d = 1.67 ft b.F=300 lb and d = 2.5 ft OcF=37S Ib and d = 3.67 ft id F=750 lb and d = 3.67 ft
A bag of laundry resting on a chair shown in (a) applies forces on the chair as shown in (b) where the perpendicular force at G is R = 35 N. Assuming the floor is smooth, determine the load acting on the chair at A in N. 0.1 m R. 0.2 m 64 N 26 N 0.3 m EF EF 0.5 m B Hk0.1 m 0.2 m
A horizontal cable exerts a force of 399.971 pounds while holding a boom into place. Determine the angle the boom makes with the ground if it supports a 1000-pound load, as shown in the figure. Include fbd, given and solution.
Two double-threaded square power screws have root diameters of 2 in. each and pitches of 0.5 in. each. Both are arranged in parallel and areused to convey a load of W = 502 lbs using a motor that rotates at 300 rpm. Determine the force F for each screw (in N) applied at the end of a lever 3 ft long if these power screws lift the given load.
Problem 2 The resultant of three parallel loads (one is missing in Fig. P-2) is 13.6 kg acting up at 3 m to the right of A. Compute the magnitude and position of the missing load. Y P 18 kg 27 kg A 0.6 m 3.4 m Figure P-2
An 87.5 kg fisherman sits at the center of the boat, which has a uniform width and a weight per linear foot of 4.1 lb/ft. The boat is 13 m long. Assume that the water exerts a uniform distributed load upward on the bottom of the boat. a. What is the applied load (lb) applied to the boat due to the weight of the fisherman? Round up to the next whole value.b. Using the applied load at Item 9.a, what is the maximum shear force (lb) exerted on the boat?c. What is the maximum bending moment (lb-ft) exerted on the boat?d. At what distance from the left side of the boat the maximum bending moment occurs?
95lall H+ Quiz 3.pdf The jih crane is pin connected at ( A) and supported by a smooth collar at ( B ). determine the reactions on the jib crane at the pin ( A ) and smooth collar (B ).The load is ( 25 kN ) as shown in the figure. 2.5m 25 kN 2 m açraa db 1:20p äc lul 21.03.03
Assume a = 4.4 ft, b = 8.8 ft, c = 17.6 ft, w = 1200 lb/ft, and P = 2800 lb. A a By= W B b Round-off answer to integer P Determine the vertical reaction forces at B and D. lb ITV C C D