3. A steel bolt through a 26-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 79 degrees Fahrenheit. The cross- sectional area of the bolt is 0.08 sq. inch and the cross-sectional area of the tube of 0.25 sq. inch. For steel: E = 30 x 10^6 psi, coefficient of thermal expansion = 6.5 x 10^-6 per degree Fahrenheit. For aluminum: E = 10 x 10 6 psi, coefficient of thermal expansion = 13.0 x 10^-6 per degree Fahrenheit. Find the thermal deformation (in inches) of the steel bolt. (Write your answer to 6- decimal places.)" Your answer

3. A steel bolt through a 26-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 79 degrees Fahrenheit. The cross- sectional area of the bolt is 0.08 sq. inch and the cross-sectional area of the tube of 0.25 sq. inch. For steel: E = 30 x 10^6 psi, coefficient of thermal expansion = 6.5 x 10^-6 per degree Fahrenheit. For aluminum: E = 10 x 10 6 psi, coefficient of thermal expansion = 13.0 x 10^-6 per degree Fahrenheit. Find the thermal deformation (in inches) of the steel bolt. (Write your answer to 6- decimal places.)" Your answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 40-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 105 MPa, of which 55 MPa is the initial stress? What circumferential stress is developed in the pipe? Why is it necessary to tighten the bolt initially, and what will happen if the steam pressure should cause the stress in the bolts to be twice the value of the initial stress? *
Q1/ The aluminum and bronze cylinders are centered and secured between two rigid end-plates by tightening the two steel bolts. There is no axial load in the assembly at a temperature of 50°F. Find the stress in the steel bolts when the temperature is increased to 200°F. Use the following data: Aluminum cylinder Bronze cylinder Each steel bolt A (in.²) 2.00 3.00 0.75 a (/°F) 12.8 x 10-6 10.5 x 10-6 6.5 x 10-6 E (psi) 10 x 106 12 × 106 29 x 106 1.0 in.- -3 in 4 in.-1.0 in. Aluminum Bronze O
A steel tube of 200 mm external diameter is to be shrunkonto another steel tube of 60 mm internal diameter.The diameter at the junction after shrinking is 120 mmbefore shrinking on, the difference of diameters at the junctionis 0.08 mm. Calculate the radial pressure at the junctionand the Hoop stresses developed in the two tubes aftershrinking on.Take E = 2 x 10³ N/mm²
Q3: (a) describe the location and function of the following: \i. Gudgeon pin ii. Rod shank ii.Large end (b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is approximately 3.2N/mm. Design the studs also for the cylinder cover. Assume the allowable hoop stress =42 N/mm' for cast iron; the allowable tensile stress for material of studs =63 N/mm?
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
The two pistons at the ends of the cylinder gradually increase the air pressure. The circumferential stress in the cylinder must not exceed 3.8 MPa. What is the maximum air pressure (in MPa) that can be maintained in the cylinder? Express your response using three significant digits. GOʻGG 50 mm Cylinder wall thickness: 3 mm
A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.
A compound cylinder is made by shrinking a jacket with an outer diameter of 200 mm on a hollow cylinder with diameter of 100 mm and 150 mm. When the compound cylinder is subjected to an internal pressure of 35MNm-2, the maximum circumferential stress in both cylinders is the same. Calculate the maximum stress developed at the internal diameter of the jacket.
Question 4 A steel rod of 20 mm diameter passes centrally through a copper tube of 50 mm external diameter and 40 mm internal diameter. The tube is closed at each end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projecting parts of the rod. If the temperature of the assembly is raised by 50°C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m² and 100 GN/m² and a for steel and copper as 12x 10-6 per °C and 18 x 10-6 per °C.
A steam boiler is to have a 300 mm diameter hand placed hole on one end. If themaximum internal pressure is 1.3 MPa, how many 15 mm holes will be required to keepthe cover plate in position? The root diameter of a 15 mm bolt is 12 mm. The allowabletensile stress in the bolts is 100 MPa and the initial stress in the bolts when they aretightened is 600 MPa.
A cylinder head of a steam engine is held on by 14bolts. The effective diameter of the cylinder is 35cm and the steam pressure is 85N/mm².Assuming that the bolts are not initially stressed; find the size of bolts if the tensile stress is not to exceed 20N/mm²
Question 1A thick-walled tube with the outer and inner diameter of 360 and 180 mm, respectively is subjected to an external pressure of 25 MPa. Assuming the open-ends condition of the tube:(a) Determine the hoop stress component at the outer wall of the tube.(b) The hoop stress in part (a) can be neutralized (zero magnitudes) by filling the tube with fluid. Determine the required magnitude of the fluid pressure in the tube to achieve this condition.(c) Compare the variations of the hoop stress and radial stress across the wall thickness of the tube for part (b). Indicate the stress values at the inner and outer radii of the tube.