3. Explain any four dynamic characteristics of measurement system.
Q: Power System Protection
A: According to question:
Q: Explain any two Data presentation Element in measurement system with neat diagram
A: Measurement system: The block diagram is given below: From the above block diagram, The primary…
Q: Explain any four dynamic characteristics of measurement system
A: Every instrument is sensitive towards some factors like heat, pressure, resistance etc. due to these…
Q: Explain the operation of thermochemical energy storage system.
A: Thermochemical energy storage systems are basically the energy stored from the sun in the form of…
Q: One of the following is the example for process control system. a. Water level controller b. Radar…
A: Cement Industry is an example of process control system.Advanced process control is used in cement…
Q: Explain any two Data presentation Element in measurement system with neat diagrams. Note:please do…
A:
Q: 3- Using the appropriate graph, explain the charging and discharging paths in a stable 555 timer.
A:
Q: Determine whether this system is memoryless, causal, and stable or not.
A:
Q: Answer the following briefly. 1- Describe control objectives for a process control.
A: Since you have asked multiple question ,we will slove the first question for you .If you want any…
Q: List three factors that would contribute to a variation between calculated and measured values.
A: There is various factors which contribute to cause in measured value . Fualty equipment Wrong…
Q: Control Systems
A: According to question: The phase cross over frequency is calculated as
Q: Write an Arduino based code to take input from two switches, if switch one is pressed than glow full…
A: The input is taken from two switches On pressing switch one, the full spectrum on RGB Led. On…
Q: 1. Briefly describe the key components of communication system with suitable diagram.
A:
Q: Explain any four dynamic characteristics of measurement system.
A: The explanation is as follows.
Q: ) Define quantitative and qualitative data.
A: a) Quantitative data:- Quantitative data are measures of values or counts and are…
Q: 9. Six determinations of a quantity, as entered on the data sheet and pre- sented to you for…
A:
Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring system
A: RTD (Resistance Temperature Detector) is an electronic device used to detect the temperature by…
Q: a) Draw the block diagram of a measurement system.
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: display. what which will be might be ১se faster? apploximate dispay time?
A: Raster Display:- It is the most common type of graphics monitor which has CRT. It is based on…
Q: Draw the block diagram of a Pressure measurement system .Also identify the names of the functional…
A: The block diagram of a Pressure measurement system is as follows:
Q: . Discuss the advantages and disadvantages of null and deflection types of
A: Advantages :- (1) Accuracy of null type instrument is high. (2) Null type instruments are high…
Q: Explain with a neat block diagram the measurement of temperature using RTD (measuring system).
A: Resistance Thermometers (RTD) Also known as resistance temperature detector And used for…
Q: Please write introduction about Verification of series RC circuit Note: (please write details by…
A: RC circuit is a resistor-capacitor circuit. RC circuit is composed of the resistor R and capacitor C…
Q: 3. Explain the successive approximation type ADC with neat schematic diagram.
A: Successive approximation ADC: The successive approximation ADC is a type of converter that converts…
Q: Make a diagram , and explain the construction, working principle and the applications of Magnetic…
A: to make a diagram , and explain the construction, working principle and the applications of Magnetic…
Q: What are electronic sensors? Who is composed?
A: Electronic sensors are the devices that are used to detect the physical quantities in any physical…
Q: is defined as the art and science of measurement and control systems.
A: Explanation: Instrumentation is defined as the art and science of measurement and control systems.…
Q: What are the risks associated with NOT implementing ISO 27001 in an organization ? What are some…
A: ISO 27001: It provides a standard framework to manage information and data for a modern…
Q: Draw the block diagram of a Displacement measurement system .Also identify the names of the…
A:
Q: Show all the necessary details
A: Given, Here, the reference voltage is Vref=6 Volts given above in the question. and the Analog…
Q: 3. Compare between indirect and direct control circuits.
A: Indirect control circuits: Cylinders with a big piston diameter demand a lot of air. To activate…
Q: please write about Small water pump on smart plant irrigation system.
A:
Q: Which 1 below is NOT PLC's configuration types Modular Unitary O Rack mounted Automation O
A: Asked that which one below is NOT PLCs configuration types
Q: 1.Explain with a neat block diagram the measurement of displacement using RTD (measuring system).
A:
Q: 8) What are the applications of the instruments and measurement systems? 9) Why calibration of…
A: 8)• Used for Regulating Trade: The measurement instruments are used to measure quantities like…
Q: List of final year software projects for Electronics and Communication Branch?
A: The list of some projects using software like MATLAB, C++, etc. are mentioned below:
Q: Q/ Mention an application an the topic 807 timization ?
A: Optimization is a process of producing good and productive results either in making products or…
Q: Music can be sampled without permission of the licensor in cases of hip-hop songs True or False?
A: No, we can't sample music without permission, no matter how short or long or which type of cases of…
Q: what are the advantage and disadvantage of the sensors that are used in the labs
A:
Q: Draw the block diagram and explain the basic components of Numeric relay
A:
Q: Which level(s) of measurement is(are) considered qualitative? * Ratio and Interval Interval and…
A:
Q: stability
A:
Q: 01: Discuss the principle of operation of the (Synchro) and the (Resolver) machines, then choose and…
A: The synchro and the resolver is electrically similar to the transformer and mechanically similar to…
Q: IDPS Terminology Discuss the following IDPS terminology: Alarm clustering and compaction Alarm…
A: Alarm clustering and compaction : The intention of alarm clustering is to address the basic alarms…
Q: 5. Labeling the pin numbers of 7432 IC
A: 7432 has 4 OR gates of 2 inputs in 1 package.
Q: control systems
A:
Q: Calculate Av and Ap
A: The required parameters can be calculated by using the DC analysis and AC analysis of the amplifier…
Q: List any 4 performance terms of a measuring system and define them.
A:
Q: recognized associations and other organized associations
A: Recognized and other organized associations have various important reasons to involve in it. Few…
Step by step
Solved in 2 steps
- The resultant DC signal from a half-wave rectifier circuit was investigated, the following trace was observed on the oscilloscope: RIGOL T'D f 0 -80.0mV CH2 500MV Time 5.000ms T+0.0000s The trace has a slight ripple in its structure. This ripple can be attributed toQ1.Explain temperature compensation of strain gauge in detail? Q2.Explain sources of noise and its type(electrical amd static noise) in detail? Q3.Explain magnetic noise in detail ? Q4.Explain crosstalk,shielding and grounding in detail ? Q5.Explain level measurement(mechanical level indicators) in detail? Explain these 5 questions please.Explain about (ZCS) zero current switching and (ZVS) zero voltage switching in steady state transient condition: a) Switching current and voltage of the switch b) output current and voltage at the load