3. For the data tabulated, calculate the volume of excavation in cubic yards between stations 10 + 00 and 15 + 00. Cut End Station Area (ft) 10 + 00 263 11 + 00 358 12 + 00 446 13 + 00 402 14 + 00 274 15 + 00 108

3. For the data tabulated, calculate the volume of excavation in cubic yards between stations 10 + 00 and 15 + 00. Cut End Station Area (ft) 10 + 00 263 11 + 00 358 12 + 00 446 13 + 00 402 14 + 00 274 15 + 00 108

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

Q: Q5. As a civil engineer, you have been assign to prepare earthwork cost estimation for a proposed…

A: A mass haul diagram provides viewers with a graphical representation of the material moved. In a…

Q: 1. Complete the differential level notes shown below, perform the customary arithmetic check,…

A: Formulas Used: 1.Mean Rdg= (Upper + Middle + Lower ) Rdg/ 3 2.S = (Upper - Lower) Rdg 3. H.I =…

Q: A prismatic shaped excavation is measured with a 1" 20' scale. The measurements are: 2" Wide x 3.5"…

A: Given: scale: 1"=20' 1"=240" width=2" length=3.5" depth=(1/2)"

Q: Calculate the total volume (m3) from Station A to B if the following cross sections were provided:…

Q: Using the average-end-area method, calculate the cut-and-fill volumes for stations 125 +00 through…

A: The average end area method is useful for estimating quantities in construction, It is an…

Q: The cross-section notes shown below are for a ground excavation for a 12m wide roadway. STA 12+1400…

Q: The cross-section notes shown below are for a ground excavation for a 12m wide roadway. STA 12+2800…

Q: The two sides of a rectangular lot were measured with certain estimated probable errors as follows:…

A: From the given data :W=253.36mL=624.15mew=±0.06meL=±0.08mso,

Q: The cross-section notes shown below are for a ground excavation for a 8m wide roadway. STA 23+500…

Q: questions by completing the tabulation below. Determine the total area of the lot in hectares.…

A: Data Given: Asked: Complete the solution

Q: Using the average-end-area method, calculate the fill volumes for station 150 + 00 through 154 + 00.…

A: FormulaAverage area =A1+A22Volume (cy)=Average…

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

Q: 4. For the data below, determine the cumulative volume in cubic yards between station 0+00.0 and…

Q: The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 16+4400…

Q: The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 23+4000…

Q: Sand Fine Gravel Coarse Gravel % % Pit1 55 25 30 15 30 Pit2 45 Pit3 25 20 55 How many cubic meters…

Q: The two sides of a rectangular lot were measured with certain estimated probable errors as follows:…

A: Given: The width is 253.36 ± 0.06 m. The length is 624.15 ± 0.08 m.

Q: Shown below is a trapezoidal area which will be excavated and used as borrow pit. It has been laid…

A: Given- Elevation=52.5m

Q: Look up the numerical value for the following factors from the interest-34 * tables (A/F,2%,16) a)…

A: Given, (A/F, 2 %, 16) It is in the form of (A/F, i, n) Here i the interest rate, and n is the number…

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

A: The area between irregular boundaries is given by Simpsons rule. Below is the attached solution.

Q: The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 13+8300…

A: To Determine the cross sectional area at STA 13+8300.

Q: b) The Figure shows a field in the shape of a grid with all the dimensions and reduced levels. If…

Q: Calculate the corrected volumes of cut and fill using the following cross section notes, with the…

A: Given data:- Side slope, S = 1 Below table is given;

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

A: The best method applicable for area of irregular boundaries is simpson one third method. Below is…

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

A: The best method applicable for determination of area of irregular boundaries is Simpson's rule.…

Q: Determine height of 2nd floor of proposed residential apartment building from figure 1 below, as…

Q: The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 17+800…

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

A: For irregular boundaries, Simpson's rule is best applicable. A=…

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

Q: A 120mx120m lot is divided into 9 equal sections. Find the volume (m3) to be excavated if the ground…

A: A Mean area method is a way of calculating points in a system area with the correct calculation.…

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

A: h1=5.8h2=4.08h3=7.84h4=7.92h5=6.02h6=4.2h7=7.75 d = station interval = 30

Q: Find the volume of excavation required for the area shown in the figure. Each grid point (20 in…

A: Depth of the cut at every location is given find the average depth of cut…

Q: A surveyor is supposed to determine the elevation at point B. (S)he starts from a known Benchmark,…

A: Given that; Benchmark=1200ft. Surveyor is supposed to determine the elevation at a point B.

Q: Problem 10 The following notes are given for a multilevel section of a road of formation width 6 m…

A: Surveying is done as a priority in engineering before the building was constructed. It involves…

Q: In the diagram shown, the correct steps for drawing a triangle starting from point B in the AutoCAD…

A: The steps are as: Draw the line of length 40.00 making an angle of 0° with horizontal. (Enter…

Q: B. Describe a practical procedure to measure the height of your house using tachometric surveying,…

Q: A private parcel was surveyed prior to the construction of a proposed fabrication plant. Table shown…

Q: The cross section notes shown below are for a ground excavation for a 10 m wide roadway. What is the…

A: Coordinates of the points are: Left Point = 8.2, 2.15. Center Point = 0, 3.5. Right Point = 13.65,…

Q: A rectangular lot area is illustrated below. Inside the perimeter of the rectangular lot are three…

A: Given data, Pace factor PF = 0.86 m/pace

Q: The cross-section notes shown below are for a ground excavation for a 8m wide roadway. STA 18+700…

A: To Determine the cross sectional area at STA 18+700.

Q: A 120mx120m lot is divided into 9 equal sections. Find the volume (m3) to be excavated if the ground…

A: Solution; Given data; Each section has an area of 40*40=1600 m2 Proposed elevation=10 m

Q: A surveyor starting from a point A moves N. 27° 40' E. a distance of 552' 7.25" to point B. Next,…

A: Whole circle bearing: The horizontal angle which is made by the line with respect to the magnetic…

Q: The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 20+700…

Q: Compute the area using Double meridian diatance or triangulation Com. Com.Dep Length (meters) Line…

A: Given data Required to find: Area by Double meridian distance method

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

A: Area : The area is the quantity of area occupied via way of means of a two-dimensional figure. In…

Q: 1. Complete the differential level notes shown below, perform the customary arithmetic check,…

Q: STATION END AREA, in sq. meters 16+220 85 17+000 110 17+820 260

Concept explainers

Volumes

Volume usually is the dimensional quantity that involves the evaluation of any three-dimensional figure enfolded inside a closed space. The SI unit (International System of Units) of volume is m3 and the dimensional unit of volume is [L3]. For estimation of the volume of any figure, various formulae are used. Another application of volume includes the reference in the sound levels, the higher the sound intensity, the louder the sound heard, and hence, the larger the volume. The SI unit of sound volume is decibels (dB).

Question

100%

3. For the data tabulated, calculate the volume of excavation in cubic yards between stations 10 + 00
and 15 + 00.
Cut End
Station
Area (ft?)
10 + 00
263
11 + 00
358
12 + 00
446
13 + 00
402
14 + 00
274
15 + 00
108

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Data

Step 2 : solution

Step 3

Step 4; ANSWER TABLE

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

eview Part A For the data tabulated, calculate the volume of excavation between stations 10+00 and 15+00 Express your answer in cubic yards to five significant figures. Station Cut End Area (ft²) 10+00 269 11+00 343 12+00 458 13+00 408 14+00 279 15+00 104 Ve= ΤΟ ΑΣΦ vec , 7 0 ? Submit Request Answer Provide Feedback yda
Station Cut End Area (ft²) 10+00 234 11+00 369 12+00 441 13+00 408 14+00 271 15+00 108 Part A For the data tabulated, calculate the volume of excavation between stations 10+00 and 15+00. Express your answer in cubic yards to five significant figures. IVE ΑΣΦ V₂ = Submit Provide Feedback Request Answer vec ? yd³
H.W\ Calculate the excavation volume from the details of cross sections shown in table below. The width of the road is 12m Cross-sections C2.07 C1.75 C2.01 C2.46 Stations 60+40 C1.62 6.93 4.5 4.5 8.19 60+90 C2.24 C2.24 C2.24 9.36 9.36 70+55 C2.13 C2.03 C1.92 9.2 8.88
Station Cut End Area (ft²) 10+00 238 11+00 353 12+00 450 13+00 408 14+00 265 15+00 104 Part A For the data tabulated, calculate the volume of excavation between stations 10+00 and 15+00. Express your answer in cubic yards to five significant figures. Ve= ΕΠΙ ΑΣΦ ΑΣΦ | Π vec w ? yd³
Station Cut End Area (ft2) 10+00 240 11+00 362 12+00 443 13+00 406 14+00 261 15+00 101 For the data tabulated above, calculate the volume of excavation between stations 10+00 and 15+00. Express your answer in cubic yards to five significant figures.
Station Cut End Area (ft²) 10+00 256 11+00 364 12+00 440 13+00 405 14+00 274 15+00 107 ▼ Part A For the data tabulated, calculate the volume of excavation between stations 10+00 and 15+00. Express your answer in cubic yards to five significant figures. ΠΙΑΣΦΗ Ve= Submit Provide Feedback Request Answer vec ? yd³ Next >
Q1/ The table shown below is obtained from a survey of a street project. Calculate the height of Fill and depth of Cut for each points. If the elevation for the design street (D.L) are equal to the G.L elevations for the stations (1, 6, and 12). Isl f.s. F P. 1 2 3 4 S 6 78 7 8 9 10 11 12 مز Bs 2.58 25 40 50 60 75 95 130 1-30 139 145 155 0.83 2.34 2.64 2,13 093 0.34 1.79 0.66 1.92 2.58 2.53 1.10 ->E=R.L=57.75m
Q3) From the data in the table below, find the total volumes for cut and fill using proper formula. NO. Station Area fill (m) Area cut (m) A1 31+00 12 32+00 33+00 A2 15 A3 19 A4 34+00 17 A5 35+00 18 A1 31+50 21 A2 36+00 19 АЗ 36+50 16 A4 37+00 14 A5 37+50 13 A6 38+00 15 A1 39+00 24 A2 40+00 22 АЗ 41+00 26 A4 42+00 21 A5 43+00 20 A6 44+00 23
For the data listed below, calculate cut, fill, and cumulative volumes in cubic yards between stations 10+00 and 20+00. Use an expansion factor of 1.25 for fills. Station 10+00 11+00 12+00 13+00 14+00 14+60 15+00 16+00 17+00 18+00 19+00 20+00 End Area (ft2) Cut Fill 0 108 238 201 106 0 0 102 138 205 147 138 106
Form the data below, find the total volume of cut and fill by using average end-area method and check by prismoidal method. Area m? Volume m' Station Cut Fill Cut Fill 5+00 12 6+00 16 7+00 22 8+00 9+00 10+00 15 11+00 19 12+00 21 13+00 24 Total
The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 19+2600 8.09 5 0 5 8.25 6.54 5 4 6 6.7 Determine the cross sectional area at STA 19+2600. Round your answer to 3 decimal places.
The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 23+4000 8.87 505 8.09 3.16 6 4 3 3.95 Determine the cross sectional area at STA 23+4000. Round your answer to 3 decimal places. Add your answer