3. Point A lies in a clayey sand layer with ' = 38, c' = 10 kPa, and Ko = 0.5. The ground surface is flat. A planned construction operation will cause the vertical effective stress at point A to reach 80 kPa. a. Use a compass to draw the expected MC for point A (after construction) on the space shown on the right. b. Will point A reach failure? Explain your answer with one sentence.

3. Point A lies in a clayey sand layer with ' = 38, c' = 10 kPa, and Ko = 0.5. The ground surface is flat. A planned construction operation will cause the vertical effective stress at point A to reach 80 kPa. a. Use a compass to draw the expected MC for point A (after construction) on the space shown on the right. b. Will point A reach failure? Explain your answer with one sentence.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter17: Settlement Of Shallow Foundations

Section: Chapter Questions

Problem 17.15P: A shallow square foundation for a column is to be constructed. It must carry a net vertical load of...

See similar textbooks

Similar questions

Q4: Use the rectangular loaded area to calculate the increase in vertical stresses at points (A) and (B) due to the loaded area of footing. Choose figure (1) or (2). Top view Top view It 10 m.X. 10m. 4-15006 AWT MPRESSIBLE CLAY 1 CLAY 1 CLAY 2 10m x 10m - 150 d 777777777 G.W.T CLAY 1 CLAY 1 CLAY 2
Q4: Use the rectangular loaded area to calculate the increase in vertical stresses at points (A) and (B) due to the loaded area of footing. Choose figure (1) or (2). 121 Top view Top view B J-2m- B CLAY 1 CLAY 1 CLAY 2 A 10 m X 10 m 9-150 kN/m² TTTTTT INCOMPRESSIBLE Figure (1) B G.W.T CLAY 1 CLAY 1 CLAY 2 YA' 10 m X 10 m 9-150 KN² INCOMPRESSIBLE Figure (2) Thm G.W.
QL: Determine the vohume of earthwork to be excavated for the plot shown in fig 1. The formation level is 69.00 m. 1t o i T ne no nn na 15m n o) g g t5m 7 710 e T Figure 1
Answer Q13 to Q 15 based on following description A cutting in a saturated clay is inclined at a slope 1 vert:1.2 horizontal and has a vertical height of 10.0 m. The bulk unit weight of the soil is 18 kN/m³ and its undrained cohesion is 35 kN/m³. Undrained friction angle, -0. Area of slip mass = 51.2 m², d= 7 m r=12m 2m 1 W 10m FoS of a slope along a circular slip surface is given by; cular F = Wd Calculate the arc length along the slip surface, La a-964.8 m O b. 16.8 m O c. 114.0 m O d. 8.4 m d=5m 1.2
4:50, 100, and 150 kN point loads are applied at Points A, B, and C, respectively, on the ground surface as seen in the figure. Compute the vertical stress increment under Point D down to the depth z=20 m. Use Vertical stress Increment under corner of rectangular footing? 150kn 7.5m 50kn 2m™ (Plane view) 3m 5m 100kn
3. Point A lies in a clayey sand layer with $' = 38, c'= 10 kPa, and K, = 0.5. The ground surface is flat. A planned construction operation will cause the vertical effective stress at point A to reach 80 kPa. a. Use a compass to draw the expected MC for point A (after construction) on the space shown on the right. b. Will point A reach failure? Explain your answer with one sentence.
A uniformly distrubuted load applied on a strip fooing constructed in sand. Based on Hansen's equations, for a given factor of safety (FoS = 3) find the required width (B). Water table is far below the base of fooing. 300 kPa m D |kN/m³ |deg kPa 20 35 C В Nq| Ny 33.3 33.9 FoS В Im
What is RQD? What kind of rock is a rock with RQD = 20?
Q₁/ Along flexible strip looting of 2.5m width howing a smooth base, is subjected to auriformt distributed load of 80 kn/m²_Determine the vertical stress intensities at adepth of 2m below: 1) center line of the looting 2.5m (1) at side lace of the losting 2m iii) at a point 1.5m. from the side lace t √₂ = ²/² [ 2² +² 옺[a+ 2 + Sin & Cos (2 + 2B)] !!
What is the boundary shearing stress (in KPa) of a rectangular channel having dimensions of b = 2.89 m and d = 4.97 m? Channel slope is = 0.056. Round off to two decimal places.
Q4: Use the rectangular loaded area to calculate the increase in vertical stresses at points (A) and (B) due to the loaded area of footing. Choose figure (1) or (2). Top view Top view it. awT CLAY 1 CLAY 1 CLAY 2 10m x 10m 150² INCOMPRESSIBLE Figure (1) B G.W.T ME CLAY 1 CLAY 1 CLAY 2 YA 10mX10m 7-15076 INCOMPRESSIBLE Figure (2)
Discuss Presumptive Allowable Bearing Pressures