3.46 The electric motor exerts a torque of S00 N •m on the steel shaft ABCD when it is rotating at a constant speed. Design specifications require that the diameter of the shaft be uniform from A to D and that the angle of twist between A and D not exceed 1.5. Knowing that TmS 60 MPa and G = 77 GPa, determine the minimum diameter shaft that can be used. 300 N. m 500 N- m B D 04 m 0.6 m 03 m Fig. P3.46

3.46 The electric motor exerts a torque of S00 N •m on the steel shaft ABCD when it is rotating at a constant speed. Design specifications require that the diameter of the shaft be uniform from A to D and that the angle of twist between A and D not exceed 1.5. Knowing that TmS 60 MPa and G = 77 GPa, determine the minimum diameter shaft that can be used. 300 N. m 500 N- m B D 04 m 0.6 m 03 m Fig. P3.46

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys Band Care as shown. Take a = 1.4 m, b= 0.9 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 300 N. m 200 N. m 45 mm 44 mm 40 mm Im Determine the angle of twist between Band C. The angle of twist between Band Cis|
The axis ABCD receives a torque of 500Nm from the motor and transmits movement to other devices, by means of belts and pulleys connected at B and C. If it is known that the torques exerted on pulleys B and C are as shown In the figure, determine the minimum radius the shaft must have. You should consider that at point D of the motor there is a bearing that acts as a support for the shaft as at point A. The material of the shaft and its allowable shear stress are indicated in the drawing.Determine:to. Free-Body diagram.b. Shear force diagrams.c. Bending moment diagrams.d. Identification of the critical point of the axis.e. Calculation of the axis radius. tperm=80MPa
The steel shaft with two different diameters rotates at 4.9 Hz. The power supplied to gear C is 54.1 kW, of which 26.9 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 55.5 mm, h = 68.9 mm, L = 4.2 m, M = 2.8 m, and G = 83.46 Gpa. Round off the final answer to two decimal places.
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.
The steel shaft with two different diameters rotates at 4.5 Hz. The power supplied to gear C is 51.7 kW, of which 30.4 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 57.3 mm, h = 68.9 mm, L = 4.2 m, M = 2.4 m, and G = 83.16 Gpa. Round off the final answer to two decimal places. A d Bh C | — L M →
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel -20KW JOKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O f segment Co is to be replaced lay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by k = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(1) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is J, = 0.05 kg-m?. Assuming the equivalent torsional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 0(1). O(1) M(1) = Mg cos etr %3! Turbine rotor, Jo
Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 mm of length. G = 80GN/m2
Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also determine the length of the shaft if the twist must not exceed 1.5o over the entire length. The maximum shear stress is limited to 55 N/mm2. Take the value of modulus of rigidity = 8 x 104 N/mm2.
1. The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the driver gear acts at a pressure angle of 20 degree. The shaft transmits a torque to point A of TA =340 N.m. The shaft is machined from steel with S,=420 MPa, Km2.5, S=134MPA and N=2. Draw shear and bending diagrams and calculate diameter of shaft. 250 mm 100 mm
Figure 1 is presented the solid shaft AB rotates at 650 rpm and transmits 30 kW from the motor machine tools connected to gears F and G. Assuming that, 10 kW is taken off at gear F and 20 k taken off at gear G, knowing that allowable torsional shear stress is equal to (65 plus last digit of student ID) MPa. Design the smallest permissible diameter of shaft AB. Figure 1 150 mm 225 mm 905 mm 150 mm 60 mm 100 mm D. 60 mm B.
Determine the diameter of a solid shaft which will transmit 440 kW at 280 rpm. The angle of twist should not exceed one degree per metre length and the maximum torsional shear stress is to be limited to 40 N/mm2. Assume G = 84 kN/mm². %3D