4- Which of the following data hazards can cause stalls in in-order pipelines: A-Read-After-Read B-Write-After-Read C-Read-After-Write D- (None) 5- For the same cache size, increasing cache associativity reduces: A-Capacity misses B-Conflict misses C- Cold misses D- (All Answers) 6- For a fully-associative cache, increasing cache size reduces: A-Capacity misses B-Conflict misses C- Cold misses D- (All Answers)

4- Which of the following data hazards can cause stalls in in-order pipelines: A-Read-After-Read B-Write-After-Read C-Read-After-Write D- (None) 5- For the same cache size, increasing cache associativity reduces: A-Capacity misses B-Conflict misses C- Cold misses D- (All Answers) 6- For a fully-associative cache, increasing cache size reduces: A-Capacity misses B-Conflict misses C- Cold misses D- (All Answers)

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

3. Draw the block diagram of a 16Gx64- ICs, bit RAM using 8G×32-bit RAM R/W external Use minimal number of components. Each RAMI IC has R/W, CLOCK, EN', Data (DO-Dm), and Address (AO-An) pins. Block diagram of the RAM IC is shown in Figure 2. You IC block gates, and decoders. CLOCK DO-Dm EN 8Gx32-bit RAM may use a gener ic decoder AO-An diagram in your solution. A Figure 2. Block diagram of a 8Gx32-bit RAM IC.
It is usual to use both row and address decoders to access each memory location in the DRAM of a practical memory system. A 256Mx1bit DRAM chip design is limited to using decoders with 13 address inputs. (b) OW What is the minimum number of banks of DRAM required in this chip? (i) (ii) How many AND gates are saved in this design compared to that using a single decoder? Ignore any multiplexers required in the design. (iii) Sketch the logic needed to select between the various banks of DRAM. Represent each bank of DRAM as a 'black box' with appropriate input and output signals.
Course: computer architecture Design an 256Kx16 DRAM memory using 64Kx4 module. Draw the block configuration of the modules showing all required input and output signals, and size of MAR and MBR.
The amount of ROM needed to implement at 4 bit multiplier is
2 - Memory Read causes data: from the addressed location to be placed on the data bus on the bus to be output to the addressed I/O port on the bus to be written into the addressed location
A common bus in a computer connects 16 source registers (each register is 32 bits) and one memory unit with word size of 32 bits also. If the bus is designed using multiplexers, answer the following: • What is the minimum number of multiplexers required? What is the minimum number of select lines each multiplexer has? If the bus is designed with three-state buffers and decoders, answer the following: • What is the minimum number of three-state buffers required? • What is the minimum number of decoders required? • What is the minimum size of each decode
An old DRAM chip has 19 address pins and 2 data pin, compute the min and max capacity in MB.
Differentiate between the function of the following 8086 IC pins: HOLD and HLDA INTR and INTA (active low) A0-A15 and AD0-AD15 Mx/Mn RQ/GT0 and RQ/GT1 (active low) B) How the clock generator chip (8284A) is used to provide the clock for the microprocessor?
Question 1 The memory mapping arrangements of four memory devices in a microcontroller is given as (a) Your Device SD000-SD3FF RAM $D800-SDFFF ROM SE000-$FFFF I/O Ports $5800-S58FF (i) Determine the total memory space of each of the four devices. (ii) Design a fully-decoded positive-logic address decoder for all four devices. (iii) Design a minimal cost, positive-logic address decoder for a component Your Device in a small embedded microprocessor system
S I32-bit wide main memory unit with a capacity of 1 GB is built using 256M x 4 - bit DRAM chips The number of rows of 1memory cells in the DRAM chip is 2 The time taken to perform one refresh operation is 50 nanoseconds, The refresh period is 2 milliseconds. The percentage
Determine the names and the values of the special function registers involved for configuring an 8051 serial port to 8-bit UART at 9600 baud rate. Assume 11.0592 MHz operating frequency.
1. design an 8 bit common bus based circuit that supports addition of two 8 bit values. There are two data registers: RegA and RegB. The adder needs to be accumulator based; this means that one operand must be found in the accumulator register, AC, and the other will be loaded from the common bus. The circuit must support AC + RegA as well as AC + RegB. 2. For example, suppose you want to add RegA + RegB. If RegA contains 1216 and RegB contains 3416, you must manipulate the circuit through control signals so that the adder can add up the AC + a register operand. You may use Adder-8 from the parts library. The sum from the adder must be loaded back into the AC. 3. The circuit must be able to move data on the bus from one register to the AC or to the adder. There are no point-to-point connections between components; however, the AC can load data either from the bus or from the output sum of the adder. You will need to include a mux to control that capability. 4. Each register, RegA,…