4. The rigid bars AB and CD shown in Fig. P- 214 are supported by pins at A and C and the two rods. Determine the maximum Figure P-214 Aluminum L- 2 m A - 500 mm E- 70 GPa force P that can be applied as shown if its vertical movement is limited to 5 mm. 3 m 3 m Neglect the weights of all members. Steel L- 2 m A = 300 mm2 E = 200 GPa 3 m 3 m

4. The rigid bars AB and CD shown in Fig. P- 214 are supported by pins at A and C and the two rods. Determine the maximum Figure P-214 Aluminum L- 2 m A - 500 mm E- 70 GPa force P that can be applied as shown if its vertical movement is limited to 5 mm. 3 m 3 m Neglect the weights of all members. Steel L- 2 m A = 300 mm2 E = 200 GPa 3 m 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
Determine the smallest safe cross-sectional areas of members CD, Cl and CH for the truss shown. The allowable stress are 100 MPa in tension and 80 MPa in compression. Indicate tension or compression. (Draw the required FBD and answer in mm2). Fa a –– a→– a- B D |E A a F G H а 3 2 т 45 kN
Q₁: Analyze the truss shown below B с <50k 3m IMI A E 100ku EA is Constant for all members + Am X Am
Aen = a0 © @2 Z Q23-7-2018p.. Q1: A railway ridge consisting of truss construction as shown in the Figure below, this truss is supported by A and B. The forces on joints il and V are i the uss result from a i crossing the railway bridge Determine the following: (a)the reactions forces in A and B (b)the forces of the truss members in joints (1.1, I and 1V) >
For the truss shown determine the member forces in EF, EG, and FG (no, this is not an error) in pounds. ( A 1,242 Ib В C 2,484 lb D E 2,484 Ib 5@5ft = 25 ft F G 1,863 lbe H. 1,242 Ib 621 lb 12 ft FEF magnitude Ib sense ---Select--- magnitude Ib sense ---Select--- FFG magnitude Ib sense ---Select---
(c) The rigid bar ABC is suspended from three wires of the same material. The cross- sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P shown. ----|--²--| A 9 DAB T L P Fig. Q1(c) PL Hint: S = note that ABC is a rigid bar. EA C
The members of the truss shown below have a cross-sectional area of 10,000 mm2. Determine the stresses in members AB and AE in MPa. Indicate if the stresses are in compression or tension. -3 m- -3 m- C E 40 kN 80 kN A 6m- 3m-
2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
Use the method of sections to solve for the following members in the Truss shown below: EF, FC, BC. Fac=2,28 Kip (C) FeF=1.11 Kip (T) FE= 1.00 kip (T) 100016 1000 16 500lb -10t 500lb D 15ft
1. Is this truss (simple, compound or complex )truss? 2. Determine the bar force in member AF of the truss shown in the figure below: * 20kN E D 2m A в 2m K 2m G 2m 2m 1 Add File
Learning Goal: To determine an l-beam's maximum bending moment, moment of inertia using the paralel-axis theorem, and the maximum stress at a given location using the flexure formula As shown, I-beam ABC supports a sign having a mass of S= 11 kg The l-beam is 740 mm long and is further supported by a rod that is attached 420 mm from the wall. Assume that all forces acting on the l-beam act along its centroid and that the l-beam's weight is negligible. Let the dimensions of the l-beam be w = 90 mm g= 25 mm, h = 70 mm j= 25 mm, c= 110 mm B Part A - Free-body diagram of beam ABC Before the problem can be analyzed, a free-body diagram must be drawn to understand the forces and reactions that act on the -bam. Drew the free-bady diagram of beam ABC. A free-body diagram includes the forces acting on the object, in this case the beam. Start your vectors at the black dots. You will not be graded on vector length. Ignore all reaction forces in the x direction, and assume all vertical reaction…
The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. 60 mm Tg = 1S00 N- m 40 mm TA = 600 N - m 250 mm 375 mm A 400 mm