5. A 2-wire DC ring distributor is 375m long and is fed with 300V at point A. At point B, 200m from A, load of 150A is taken and at point C, 100m in the opposite direction, a load of 100A is taken. If the resistance per 100m of single conductor is 0.03, find: i. Current in each section of distributor ii. Voltage at points B and C iii. Point of minimum potential List Out ahy two limitations of fuse.5. A 2-wire DC ring distributor is 375m long and is fed with 300V at point A. At point B, 200mfrom A, load of 150A is taken and at point C, 100m in the opposite direction, a load of 100Ais taken. If the resistance per 100m of single conductor is 0.03, find:i. Current in each section of distributorii. Voltage at points B and Ciii. Point of minimum potential

Answered: Image /qna-images/answer/998bc5f0-69b8-4c1d-af0f-cba22ff3cea7.jpg

5. A 2-wire DC ring distributor is 375m long and is fed with 300V at point A. At point B, 200m from A, load of 150A is taken and at point C, 100m in the opposite direction, a load of 100A is taken. If the resistance per 100m of single conductor is 0.03, find: i. Current in each section of distributor ii. Voltage at points B and C iii. Point of minimum potential

5. A 2-wire DC ring distributor is 375m long and is fed with 300V at point A. At point B, 200m from A, load of 150A is taken and at point C, 100m in the opposite direction, a load of 100A is taken. If the resistance per 100m of single conductor is 0.03, find: i. Current in each section of distributor ii. Voltage at points B and C iii. Point of minimum potential

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.16MCQ: In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across...

See similar textbooks

Similar questions

A 2-wire d.c. ring distributor is 300 m long and is fed at 240 V at point A. At point B, 150 m from A, a load of 120 A is taken and at C, 100 m in the opposite direction, a load of 80 A is taken. If the resistance per 100 m of single conductor is 0.030. find: (i) current in each section of distributor (ii) voltage at points B and C.
A 2-wire D.C. Ring distributor is 300 m long and is fed at 240 V at point A. At point B, 150m from A, a load of 120A is taken and at C, 100m in the opposite direction, a load of 80A is taken. If the resistance per 100m of single conductor is 0.03 Q, Find the voltages at all loading points and find the power dissipated in the distributor. Clearly draw the distributor, show all currents and loading points. BIEE Paragraph
The property of insulating material which makes the breakdown voltage high in a cable is ...... Good Mechanical strength O High conductivity O High dielectric strength O High insulation resistance
Derive the formula and relation for voltage and current in a pure resistive- AC circuit and prove that in this type of circuit, the current and the voltage are always in phase.
Discuss causes of insulation failures in high voltage engineering. High voltage engineering
If we increase the load than core loss and copper loss will... Decrease Increase Remain same
A 2-wire d.c. ring distributor is 300 m long and is fed at 240 V at point A. At point B, 150 m from A, a load of 120 A is taken and at C, 100 m in the opposite direction, a load of80 A is taken. If the resistance per 100 m of single conductor is 0-03 Q, find :(i) current in each section of distributor(ii) voltage at points B and C * IA 150 m 120 A в A 240 V 100 m I - 120 IA - 200 80 A
A 650 m, 2-wire d.c. distributor fed from one end is loaded uniformly at the rateof 1-6 A/metre. The resistance of each conductor is 0.0456 ohm per metre. Find the voltage necessary at feed point to maintain 240 V (i) at the far end (ii) at the mid-point of the distributor.
An RLC series circuit connected to a 110 – volt and 50 – cycle AC source, contains the following series resistances and reactances: R1 = 10 ohm, R2 = 15, R3 = 5 ohms, XL1 = 20 ohms, XL2 = 25 ohms, XC = 40 ohms. Find the following: a.) EQUIVALENT REACTANCE b.) TOTAL IMPEDANCE c.) VOLTAGE DROP ACROSS THE CAPACITOR d.) TOTAL INDUCTANCE IN MILLIHENRY e.) TOTAL CURRENT f.) REACTIVE POWER g.) REAL POWER DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES
There era two type of currents, a. direct current and b. alternating current. For each of these type, name as many as you can the specific application and discuss them as to their effectiveness And safety.
B. Define ( resistance, reactance, impedance. rks rks
Calculate element and welding currents with mesh analysis.