5. Water is being heated in a closed pan on top of a range while being stirred by a paddle wheel. During the process, 30 kJ of heat is transferred to the water, and 5 kJ of heat is lost to the surrounding air. The paddle-wheel work amounts to 500 Nm. Determine the final energy of the system if its initial energy is 10 kJ. 5 kJ JB 500 N-m 30 kJ

5. Water is being heated in a closed pan on top of a range while being stirred by a paddle wheel. During the process, 30 kJ of heat is transferred to the water, and 5 kJ of heat is lost to the surrounding air. The paddle-wheel work amounts to 500 Nm. Determine the final energy of the system if its initial energy is 10 kJ. 5 kJ JB 500 N-m 30 kJ

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 27RQ: How many Btu/h would be produced in a 12-kW electricheater?

See similar textbooks

Similar questions

2) The energy consumed by a shower for 30 days is 22kwh. It is known that the resistance of the showerhead is 20 ohms and that its nominal current is 15A. So, what is the time in minutes that the shower was turned on during this period?
A container maintains a constant pressure of 40800 Pa while changing to a volume of 791 liters. If 31080 J of work was done by the gas, what was the starting volume? *
Water is to be pumped from the bottom of a well 20 ft deep with a specific heat of 1 BTU/lbm F is pumped using a 1-hp jet pump. Heat is lost from the whole system at the constant rate of 500 BTU/min. What is the temperature (℉) of the water as it enters the storage tank assuming that the well water is at 35℉?
An electric motor is used to drive the shaft of a small water pump. During a performance test, the torque on the motor shaft is found to be 5.549 N.m when the motor is drawing 687.12 W of electrical power. What's the rotational speed of the shaft in rpm?
A mass of 6.7 kg of steam is contained within a piston-cylinder assembly. The steamundergoes an expansion from its initial state with e1 = 2617.6 kJ/kg to its final statewith e2 = 2506.2 kJ/kg. During the process there is a heat transfer of 72 kJ to thesteam. Also, a paddle wheel does 33 kJ of work on the steam. Calculate the amountof work (kJ) done by the steam on the piston during the process. Please show all work
during the working stroke of an engine the heat transferred out of the system was 160kJ/kg of working substance. the internal energy also decreased by 405kJ/kg of working substance. Determine the work done
A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 Ib/ft^3 and discharge it with density of 0.304 lb/ft 3. At the suction P1-15 psia: at discharge. P2-80 psia. The increase in the specific internal energy is 33.8 BTU/b and the heat transferred from the air by cooling is 13 BTU/lb. Determine the work on the air in BTU/lb. Neglect change in kinetic energy
An amount of gas inside an insulated vessel contained 45000J of internal energy. The gas expands until the internal energy reduced to 23kJ. Determined the work produced by the gas
K ces Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Water is pumped from a lake to a storage tank 15 m above at a rate of 98 L/s while consuming 15.4 kW of electric power. Disregarding any frictional losses in the pipes and any changes in kinetic energy, answer the questions that follow. We take the density of water to be p = 1000 kg/m³. 15 m Pump Storage tank Determine the overall efficiency of the pump-motor unit. (You must provide an answer before moving to the next part.) The overall efficiency is %. 2
A gas is compressed from an initial volume of 5.75 LL to a final volume of 1.24 LL by an external pressure of 1.00 barbar . During the compression, the gas releases 125 JJ of heat. What is the change in internal energy of the gas?
In a certain process, the working fluid is cooled until 100 Btu/lbm has been extracted as heat. During this process, 100 ft.·lbf/lbm of fluid is added as work. If the working substance undergoes a change in temperature from 100°F to 50°F, what is the specific heat of the process in Btu/lbm-R?
On a cold winter day, the rate of heat transfer from the air in a certain room is 5500 Btu/hr. The room is heated by a heating system, and the warm air is circulated by a fan which develops 0.75 hp. What is the required rate of heat transfer in kW, from the heating system in order to maintain constant room conditions?