5.42 (See Fluids in the News article titled "Bow thrusters," Section 5.2.2.) The bow thruster on the boat shown in Fig. P5.42 is used to turn the boat. The thruster produces a 1-m-diameter jet of water with a velocity of 10 m/s. Determine the force pro- duced by the thruster. Assume that the inlet and outlet pressures are zero and that the momentum of the water entering the thruster is negligible. V= 10 m/s #

5.42 (See Fluids in the News article titled "Bow thrusters," Section 5.2.2.) The bow thruster on the boat shown in Fig. P5.42 is used to turn the boat. The thruster produces a 1-m-diameter jet of water with a velocity of 10 m/s. Determine the force pro- duced by the thruster. Assume that the inlet and outlet pressures are zero and that the momentum of the water entering the thruster is negligible. V= 10 m/s #

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The jet of a horizontal nozzle strikes a vertical plate with a force equal to 7000N. If the discharge flowing at the nozzle is 0.12 m3/s. Compute the diameter of the jet. O 41 mm O 51 mm 61 mm O 71 mm
P2.) An open trapezoidal tank having a bottom width of 3 m is 2 m high, 1.5 m wide, and has its sides inclined 60° with horizontal. It is filled with water to a depth of 1.5 m. if the tank is accelerated horizontally along its length at 4.5 m/s², how much water is spilled out? Answer: ?. ? ?³ Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
Q-9 A horizontal nozzle of 30 mm diameter discharges a steady jet of water into the atmosphere at a rate of 15 liters per second. The diameter of inlet to the nozzle is 100 mm. The jet Impinges normal to a flat stationary plate held close to the nozzle end. Neglecting air friction and considering the density of water as 1000 kg/m³, force exerted by the jet (in N) on the plate is
8.) A liquid having a sp.gr. of 20 is flowing in a 50 mm diameter pipe. The total head at a given point was found to be 17.5 Joule per Newton. The elevation of the pipe above the datum is 3 m and the pressure in the pipe is 65.6 kPa. Compute the velocity of flow and the horsepower in the stream at that point. Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
The double pulley shown weighs 15 kg and has a centroidal radius of gyration of 160 mm. Cylinder A and block B are attached to cords that are wrapped on the pulleys as shown. The coefficient of kinetic friction between block B and the surface is 0.25. Knowing that the system is released from rest in the position shown, determine (a) the velocity of cylinder A as it strikes the ground in m/s 150 mm B 10 kg 250 mm 12 kg 900 mm move/copy question to another
The ball B of negligible size rolls through the tube such that at the instant shown in (Figure 1) it has a velocity of 5 ft/s and an acceleration of 3 ft/s², measured relative to the tube. Figure @, a -2 ft- B y < 1 of 1 Part A If the tube has an angular velocity of w = 3 rad/s and an angular acceleration of a = 5 rad/s² at this same instant, determine the velocity of the ball. Enter the components of the velocity separated by commas. Express your answers in feets per second to three significant figures. VBz,VBy, VBz = Submit Part B aBz, aBy, aBz = Submit V—| ΑΣΦ. 41 Request Answer Provide Feedback Determine the acceleration of the ball at this same instant. Enter the components of the acceleration separated by commas. Express your answers in feets per second squared to three significant figures. 195| ΑΣΦ. 41 vec Request Answer vec ? wwwww ft/s ? ft/s²
An open tank filled with water and pulled at inclined surface as shown. Compute the acceleration which keeps the water surface at the position shown in fig. compute pressure at point(A) before and after acceleration. az ax 1.0m 1.40m A Static surface 3 Accelerated surface
docs.google.com/forms/d/ Switch account Required In the Fig. is shown the cross-section of the tank full of water under pressure. The length of the tank is 3 m. An empty cylinder lies along the length of the tank on one of its corners as shown. Find the horizontal and vertical components of the force acting on the curved surface LMN of the cylinder. * 2 35KN/m L 12 m Tank full of liquid s=0.85 IN Empty cylinder Your answer Back Next w 7>
The double pulley shown weighs 15 kg and has a centroidal radius of gyration of 160 mm. Cylinder A and block B are attached to cords that are wrapped on the pulleys as shown. The coefficient of kinetic friction between block B and the surface is 0.25. Knowing that the system is released from rest in the position shown, determine the total distance that block B moves before coming to rest, in meters. 150 mm 10 kg 250 mm 12 kg 900 mm
Shift F Ct Z × Alt 4- An object, 12 cm in height with sides that each measure 5.0 cm, is floating in a pool of fluid. The object is steel with a density of 7850 kg/m'. If the fluid is mercury, determine "X," the distance the cube is submerged. Locate the center of gravity, the center of buoyancy and the metacenter. Determine if the object is stable in the position shown. Fluid surface X 5 cm 12 cm 5 cm Mercury Sg-13.54 All
Question- A circular shaped hatch closes the outflow of a tank. a) Determine the mass m, such that the hatch opens if m is attached in the distance e from the hinge point. b) Determine the distance by which the mass m has to be shifted, for the hatch to open when the water level reaches B 45° the height b. Given: a, b. c. d, e, m. p.
A cylindrical tank is spun at 300 rpm with its axis vertical. The tank is 0.6 m high and 45 cm diameter and is completely filled with water before spinning. Calculate the level to which the water will return when the tank stops spinning. Unit of the Correct Answer: mm An open cylindrical tank having a radius of 0.30 m. and a height of 1.20 m. is filled with water at depth of 0.90 m. How fast will it be rotated about its vertical axis so that no water will be spilled out? Unit of the Correct Answer: rpm